tips for removing not budging 27mm nut for parking brake drum access?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

You can buy a cheap 1/2" impact wrench at Harbor Freight for around $30 or so...they might not last long but for the few things I've ever really needed it for mine's been fine for quite a few years now. Not having the same kind of strength, us chicks depend on tools! Don't forget impact sockets...and a face shield, or at least safety glasses. I gotta admit...it's almost fun to hear someone else struggle with the simple stuff. It's where I live! Good luck!
 
A half inch breaker bar and socket will go a long way towards ending this issue for you....


Do not worry about ' removing the tab' crap...I have not done that, EVER. Just put the socket on there and break it loose....done deal.

(it really is that simple, when you have the right tools) :)


Good luck!


-Steve
 
Big tools and pb blaster will fix anything. Try to tighten the nut. Sometimes it will break the corrosion loose eisier and then it turns right off. The next step is heat.
 
You need a bigger tool.

All jibes aside, 3/8ths is okay for basic wrist work, but if you need to lean into it with the full arm you gotta have at least 1/2" set.

If you plan on keeping your rig for awhile, save some pennies and buy a decent air-compressor. Garage life gets soooooo much easier. It took me 10 years to reach this epiphany. But now my impact wrench, air-ratchet, and even the basic blower simplify chores to an incredible degree, both on the mechanic and woodworking sides of my hobbies.

azlar
 
The first time I did this on my 40, it was tighter than witch's...well you know what I mean. It was cotter pinned, which I got off. Then, I hammered a 1/2 inch drive socket in there (PO had distorted the nut), applied my 18 inch breaker bar wrench, extended it with a heavy walled steel pipe, and beat the end with a 4 lb mallet.

Now-a-days, air is good.

That is all.
 
1/2" breaker bar with 4' of pipe extension, it will walk right off....either that or put the breaker bar on and put it in reverse or forward (whichever way will back off the nut) and let the breaker bar rest on the frame, and then pop that clutch :) works for the front of the engine, should work for the rear...

bk
 
yep, 1/2 did the trick. like butter with a 4 foot braking bar. bigger tool does help!
 
Poser said:
A half inch breaker bar and socket will go a long way towards ending this issue for you....


Do not worry about ' removing the tab' crap...I have not done that, EVER. Just put the socket on there and break it loose....done deal.

(it really is that simple, when you have the right tools) :)


Good luck!


-Steve

got it with the 1/2!

now, how the heck do you get the seal out that is behind the drum so to stop the leaking? I bought the entire parking brake and seal kit and speedit sleeve, but how do I get the old seal out as you cannot get behind it to tap it out?
 
Tap a screwdriver between the edge of the seal and it's seat and scrunch it out of there.
 
wantatlc said:
got it with the 1/2!

now, how the heck do you get the seal out that is behind the drum so to stop the leaking? I bought the entire parking brake and seal kit and speedit sleeve, but how do I get the old seal out as you cannot get behind it to tap it out?



Good to hear!


You will need to remove the parking brake backing plate in order to get to the seal. A flat tip screwdriver can be used to pry it out, as can a seal hook/remover. These are a great, inexpensive tool that most well stocked auto parts houses should have. Looks like a thin lever handle, with a hook on opposite sides of one another.


Undo the retainers/pins that hold the shoes in place after removing the springs, and move the shoes out of the way. No need to take them off the cable.


Good luck!


-Steve
 
got it out. used a screw driver at an angle all the way around. destroyed the seal in the process, but I was replacing it anyway.

boy, that was a pain the the a$$. but, got seal changed. parking brake cleaned and fixed and working, fluids topped off, speedit sleeve in, stopped some leaks (at the seal and in the speedo cable with new o-rings and washers). long job for a novice.

case closed!
 
Back
Top Bottom