Series 80 Dash switch bezel / any interest???

[cavboy78]

I'm in! Loving the console insert cup holder btw...

 

[bhicks]

Sweet. Looks like we have plenty of interest to make this project happen.

 

[wearsabrowncoat]

Those round holes are screw access points I believe.

Correct. If you pull out the cubby you will see the two screws that help secure that side of the dash and what the bezel will be secured with.

 

[INSANE1]

You going to make a mic holder to

 

[Tredwards]

I don't know if anyone already asked, how about making mic holder too. I need an extended one

 

[NLXTACY]

The package was too late to send out today but will go out in the morning @bhicks. The local guys kept me busy today.

 

[JCruse]

At $20-$25 I'd like one too even though I don't have a definite need/use yet. If needed to make the run I'll buy now, if not I'll grab one off your website later on. Either way is good for me.

 

[bhicks]

I don't know if anyone already asked, how about making mic holder too. I need an extended one

What I'm thinking is about making the two holes on the sides threaded with different inserts like a mic mount or possible cell mount/etc. Don't know how much space I have to work with so I don't want to commit to any ideas until I start pulling dimensions off the current design. There may not be enough space for anything extra.

 

[PDoyle]

I'm in for one.

 

[Tredwards]

What I'm thinking is about making the two holes on the sides threaded with different inserts like a mic mount or possible cell mount/etc. Don't know how much space I have to work with so I don't want to commit to any ideas until I start pulling dimensions off the current design. There may not be enough space for anything extra.[/QUOTE

I am wondering about the horizontal extended mic holders that go in place of a knock out. I was planning on putting my CB on the lower left side just next to the rear heater switch.

 

[msapers]

I'm in. Also, if you need an 80 for R&D, mine is available.

 

[bhicks]

I'm in. Also, if you need an 80 for R&D, mine is available.

I have a buddy that lives right near me with an 80 series but his is a 93 and I can't remember if the 91-94 dash has the pull up cup holder tray/dash hole. Anyone know if the early 80's have the same cubby?

 

[QuarterPint]

I'm a bit late to the party but I'd be a go for one as well. If you need to run this as a group buy I'm down but I'd rather couple it with the console insert cup holder!

 

[KingDan]

Mine is a 94 and I don't have the cup holder dash slot/hole.

I have a buddy that lives right near me with an 80 series but his is a 93 and I can't remember if the 91-94 dash has the pull up cup holder tray/dash hole. Anyone know if the early 80's have the same cubby?

 

[bhicks]

Mine is a 94 and I don't have the cup holder dash slot/hole.

Ok. That means I need access to a 95-97 here in Socal. Preferably in the IE. I'm up near Big Bear(Forest Falls to be exact) and work in Yucaipa. Anyone near either of those areas?

 

[msapers]

I live in L.a. but I have a place in Big Bear, so I'm familiar with Forrest Falls right off the 38. Mine is a 1997.

 

[bhicks]

I live in L.a. but I have a place in Big Bear, so I'm familiar with Forrest Falls right off the 38. Mine is a 1997.

You going to be heading up to Big bear in the 80 any time soon?

 

[retrofive]

Sorry if this was answered. So gamiviti is not making the dash insert AND the mic holder? Im really interested in just the mic holder snapin to replace to of the worthless coin holders in the center console of '94.

More direct, will be be making both? Only catch is the orientation would be vertical for my intended use.

 

[ThunderRolls]

I'll buy two. Put me down.

 

[jtwopark]

The package was too late to send out today but will go out in the morning @bhicks. The local guys kept me busy today.

Sorry! It was a fun day though!