Roof Gutter

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

My thoughts exactly!

Not sure why anyone would do the liner on a hardtop unless they are trying to emulated the J**p look (sorry, couldnt resist). Fiberglass is not subject to rust and the course surface is hard to clean and starts to look grungy and stained after a trail ride or two, especially white. In my experience, the part that rusts is the inside gutter where water seeps in under the cap or moisture condenses and lays in the trough on the inside where it doesn't evaporate out as quickly.

SEM is probably the only choice now, and I'm not sure how good the bond will be to the liner. No matter what, that gap will need to be filled and sealed well or else the cancer will soon be back.

Will the roof rack clamps dig in too deeply on the softer sealants like SEM or Sikaflex? I read somewhere that you can't use a gutter mounted rack if you use the RV stuff that doesn't harden. Makes sense, but does anyone have actual experience with SEM or Sikaflex and roof racks? Too late for me, but just curious for future reference.
 
Last edited:
I lined the roof because the entire project is going to be lined, AND I wanted some extra sound and heat insulation because I'm adding AC in Florida.

The rivets have silicone under them from a previous redo I think, and there were no indications of leakage at all...very little rust anywhere. I've ordered dicor and will use that. Seems like its made for this application.

D
 
FL sun can turn a hardtop into an oven. I had a white OEM softtop back in the early 70's and it would cook the top of your head in July-Aug.

Are you putting insulation on the inside as well or just headliner? I've been contemplating a layer if 1/4" ensolite instead of headliner if I can find a light enough color of foam. Dynamat under headliner will work, but headliner breaks down too quickly IMO.
 
Last edited:
Gutter

After much going back and forth. SEM is THE stuff to use in your gutter..Went on like a charm, but for future reference, it takes 3 7oz. tubes of the stuff. I bought 2 of course in keeping with Murphy's law. The good news is that it went down easily..adhered perfectly, and the cold joints will be fine where I came back and finished. I will need to sand a bit in one spot where it overlapped.

I am still debating if its worth painting the stuff white..seems like a ton of work when it isn't necessary, and you can't really see it from eye level.

I'm sure Dicor would have worked, but this stuff just self leveled so nicely, and went on so easily...It would have been nice if they made it in white, but ...meh

Thanks to Splangy for talking me in to it AND letting me use his SEM gun.
20130403_163609[1].webp
 
insulation

The plan is to see how much thermal and sound protection I get from the Line-X. The guy who sprayed it says he does service vans inside and top, and it cuts down noise and heat dramatically. The nice thing is that I can put up dynamat (or something else) and headliner if I decide to after the fact.

FL sun can turn a hardtop into an oven. I had a white OEM softtop back in the early 70's and it would cook the top of your head in July-Aug.

Are you putting insulation on the inside as well or just headliner? I've been contemplating a layer if 1/4" ensolite instead of headliner if I can find a light enough color of foam. Dynamat under headliner will work, but headliner breaks down too quickly IMO.
 
The plan is to see how much thermal and sound protection I get from the Line-X. The guy who sprayed it says he does service vans inside and top, and it cuts down noise and heat dramatically. The nice thing is that I can put up dynamat (or something else) and headliner if I decide to after the fact.

My situation is nearly identical to yours, so I have bookmarked this thread. My roof project has started and stopped a few times, but I am finally at the point where I'm ready for the rivets and the SEM sealer.
 
Thank you, Splangy. I'd like to be back on the road this month. I've put the side panels and the ambulance doors back on, so the only thing left is the roof.

Was it difficult to separate the fiberglass top from the sides? I'm thinking about painting my top, but want to leave the rest attached to the 40 while it's being done.
 
Me.
That's what I recommended to the 50 or so people who bought rain gutters from me. They all seemed happy. I sent 12 tubes to Theo in South Africa for 6 rain gutter kits I sold him. Maybe he can chime in here.

Albeit late, everything that Alex sold us, was top quality.I attached my gutter with a combination of rivets and Wurth's version of Sikaflex, as it is also MCU & Xylene based.Thereafter I sealed it with the 3M sealer that Alex supplied and I am very happy - easy to work with, levelled nicely, dried hard and took the paint nicely :cheers:
 
Was it difficult to separate the fiberglass top from the sides? I'm thinking about painting my top, but want to leave the rest attached to the 40 while it's being done.

It's easy, but it takes some time. There are a bunch of bolts that hold the top on (10mm, I think). Most of the bolt heads are under the roof rail, but some in the very back are the opposite. You'll also have to remove some screws on the windshield frame, and there are some bolts above the front doors that you'll need to access. If you have more questions, send me a PM, and I'll have my son draw a diagram.
 
Back
Top Bottom