random question on CDL

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 1, 2006
Threads
211
Messages
1,010
Location
Dallas, TX
just installed CDL and 7 Pin...

What would happen if a passenger hit the the CDL switch when I was driving on the highway going 60 mph?

Would having a CDL switch make me have to watch what passengers touch on the truck... what about if my wife hits it ... doesnt know any better and runs around town with it on?
 
That's a good question, one that I have wondered (and feared the answer).

My father in-law borrowed my truck one time, and I told him: "Whatever you do, do not push that button or touch that dial!!" :frown:
 
Although I haven't done it on my 97, I have done this many times on my old 91 and it didn't do any damage :cool:

In fact, when it engaged, the drivetrain seemed to tightened up a bit and was less clunky :)

As long as the front and rear driveshafts are turning at the same speed, I don't see it posing a problem...
 
your abs light might not turn off until you stop and restart the engine.

This is my first winter with the selectable CDL dash switch and I tried it out the other day (in Hi range with the 7 pin mod) after NH got the recent ice storm.

There were parts of the roads that were covered with ice and some parts that were clear.

I drove about 3 miles at about 30mph and when I disengaged the CDL, the CDL light went out, but the ABS light stayed on. Upon restart, the ABS light did go out.

QUESTION: When the ABS light stays on after the CDL has been disengaged, does this indicate something?
 
Yes, it means your ABS isn't working ;p

Constructive answer, SNAKE EATER; thanks. ;p

I mean, is there a certain driving condition that leads to the ABS light staying on. Is there something I did incorrectly that caused this? Could intermittent dry pavement make something go screwy?

The ABS light only stayed lit once; for that particular trip. Otherwise, in the past, I have disengaged the CDL and the ABS light has followed suit. Is it driver error or just an 11 year old vehicle?

EDIT: I don't recall doing so, but it's possible that I switched the CDL button on and quickly turned it off (because I saw dry pavement ahead). Perhaps this is what you were saying, bpassmore. If you quickly engage/disengage the CDL, the ABS light will stay on until restart.
 
Constructive answer, SNAKE EATER; thanks. ;p

I mean, is there a certain driving condition that leads to the ABS light staying on. Is there something I did incorrectly that caused this? Could intermittent dry pavement make something go screwy?

The ABS light only stayed lit once; for that particular trip. Otherwise, in the past, I have disengaged the CDL and the ABS light has followed suit. Is it driver error or just an 11 year old vehicle?

Once you go over a certain speed with the CDL locked, the ABS goes into a safe mode and will remain inactive until reset (restart)
 
Ah, didn't know about the "safe mode".

Thanks (for real this time), SNAKE EATER.
 
what the heck, do you all have people riding around with you that just decide to reach over and start pushing buttons and flipping switches?
 
what the heck, do you all have people riding around with you that just decide to reach over and start pushing buttons and flipping switches?

I lectured my wife for like 5 minutes on what the CDL switch does, and quizzed her on it. She probably doesn't remember much from it, but she knows enough not to touch it!
 
No need to worry about flicking on the cdl at high speeds. I have done it a few times and all that happens is the abs stays disengaged until you restart the truck. Mechanically there should be no issues as all the wheels are spinning at the same rate so the viscous coupling should not be engaging. BTW, my truck handles better on gravel and icy roads with the cdl engaged when driving aggressively. Before anyone jumps on me, I did this to familiarize myself with the handling characteristics of the truck and do not recommend driving around with the cdl engaged for the fun of it.
 
FWIW I routinely do this to make sure things are still working. I do it on a straight section of road and unlock before the next curve.

You want to avoid locking any diff when there is a significant difference in rotational speed between the 2 halves.
 
Back
Top Bottom