Radiator

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 10, 2006
Threads
99
Messages
501
Location
The Ghetto
Just as I get the drive shaft fixed and with the correct bolts, I take a 30 mile trip (mostly interstate). When came to the end I noticed a leak coming from the front. It was radiator fluid. It was like the radiator had an STD and it was trying to pee :crybaby: Is there something I can plug this with or do I need a whole new radiator? Also, I tried taking the cap off (when it was a cold engine:grinpimp: ) to put some water in and I couldn't get it off. Is there some kind of Jedi trick to get this off?
 
Just remove the radiator and take it to a radiator shop. Have them check it out. If the truck wasn't overheating, the leak can be repaired and you won't need to purchase a new one. If the truck was overheating, then maybe you should look at replacing with new.
 
If the stock rad was ok before it was leaking than a stock rad would be ok as a replacement. I have a stock rad and running a 350 sbc.
 
Stock rad is a bandaid on a Chevy V8..

Get an al one..
 
I have run my stock rad/sbc for years and live in the Calif desert. Over 20 years of driving with no over heating problems. My first fj was also Chevy powered and stock rad and it had no overheating problems. I believe if the rad is in good shape and the engine isn't crammed against the firewall a stock rad will keep the beast cool.
 
I have no V8, but many a V8 conversion does not include a good shroud to allow the fan to do it's work. So I have to ask....do you have a shroud? Do you have an overflow/recovery tank? Did you recently top off the coolant?
Mine would always puke a little coolant until I installed a recovery system.

GL

Ed
 
I have always run a shroud, but no recovery on the 73. The 70 I used to have did have a recovery.
 
llih said:
I have always run a shroud, but no recovery on the 73. The 70 I used to have did have a recovery.
What pressure radiator cap are you running to keep the coolant from coming out as the normal increase in coolant pressure from the heat of the engine and the flow thru the water pump, especially at highway speeds. Engine manufacturers design the coolant system for their engines to run within a predetermined range and the recovery tank is the support mechanism that holds the fluid until the pressure drops below a predetermined value and is drawn back in. If coolant was not supposed to purge from the radiator they wouldn't have pressurized caps. Just think of the added stress you are putting on you heater core, hoses and fittings.
 
Not sure what kind of pressure cap i'm running. But this is n't the first time this has happened. I sprung a leak and I think just to alleviate the needed stress to try and fix something....I might just get a new one. Maybe aluminum. Any ideas on a new aftermarket one? It doesn't matter if it's aluminum or not.
 
Last edited:
I want to say a 13lb cap but it could be more or less. I lose very little coolent. I always keep extra on hand and check weekly in the summer. My temp range is between 160-185F. It did go up to 200F a couple of times when it was extremly hot out (115F). I had a recovery on the 73 for a while, but couldn't keep the tank from coming loose. I scrapped it years ago. Most of the time the 73 runs about 170-175. I just replaced the engine mounts which lowered the engine. I was previously using the downey front saddle mount. The lowered engine necessitated the replacement of the flex fan. I switched to a hi cfm Volvo electric fan shroud. Now the temp goes up a bit till the fan kicks in (190) then the temp drops like a rock. Maybe even a bit cooler then the flex . The volvo shroud is better then the one I had with the flex. I had the rad rodded out years ago and a couple of leaks fixed. After putting in the electric fan I let the truck idle for well over an hour, to see if it would over heat. It was 85-90F out at the time. Once the fan kicked in the temp didn't move from 175F. I have the fan wired so that it stays on till the temp drops.
This vehicle was my daily driver for years. I used to drive it up and down the Devore pass everyday with no overheating problems. I have owned the truck for over 30 years
 
Last edited:
llih said:
I want to say a 13lb cap but it could be more or less. I lose very little coolent. I always keep extra on hand and check weekly in the summer. My temp range is between 160-185F. It did go up to 200F a couple of times when it was extremly hot out (115F). I had a recovery on the 73 for a while, but couldn't keep the tank from coming loose. I scrapped it years ago. Most of the time the 73 runs about 170-175. I just replaced the engine mounts which lowered the engine. I was previously using the downey front saddle mount. The lowered engine necessitated the replacement of the flex fan. I switched to a hi cfm Volvo electric fan shroud. Now the temp goes up a bit till the fan kicks in (190) then the temp drops like a rock. Maybe even a bit cooler then the flex . The volvo shroud is better then the one I had with the flex. I had the rad rodded out years ago and a couple of leaks fixed. After putting in the electric fan I let the truck idle for well over an hour, to see if it would over heat. It was 85-90F out at the time. Once the fan kicked in the temp didn't move from 175F. I have the fan wired so that it stays on till the temp drops.
This vehicle was my daily driver for years. I used to drive it up and down the Devore pass everyday with no overheating problems. I have owned the truck for over 30 years
I'm running the stock factory cap and you can see the rise in coolant in my recovery tank every time I drive it. I'd say on average the tank volume doubles once the vehicle has been run for a while. When it cools it goes back in. I have a thread on replacing the factory recovery tank and have been running it for over three years without the tank becoming loose.
https://forum.ih8mud.com/showthread.php?t=95803
 
Ok. Unfortunately, my temp was going over 220 and even upwards of about 250. That is if my gauge is accurate. Anyhow, I need a new radiator so where could I find one for a V8?
 
Either get one of the ones designed for a LC that is Aluminum if you do not have the fab skills (you end up paying more) Or get a $160 AL radiator that is the size you want and make it fit..

But you do need a shroud..
 
I just dropped in a BeCool #62167 from Summit to cool my 5.7l Vortec. Installed in less than 2 hours (new thermo and complete flush). I've been running the radiator for 2 weeks and the temp rarely goes above 190. I had to can my old shroud. BeCool's claims of 20- temp drop is no bull. With my old 2 core shrouded I could bring it up to 200+ on some of the grades around here. I know your looking for something cheaper, but for me it was worth every penny. Can't wait to get my tranny gauge working again to see the temps.
 
Back
Top Bottom