please help me get her running better...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 12, 2005
Threads
59
Messages
259
Website
www.geocities.com
Hello,

I have recently gone through and cleaned the carb, changed some parts with an SOR carb rebuild kit, and replaced. While it did help the truck (1970 fj40 with stock engine) to run leaner, she's not running the best. I still need to have the choke all the way on to idle, even when warm.

I know that I'll need to set the idle screw which will help a lot, but I'm affraid the motor is tired and soon to die. There's oil all over the place (appears to be slowly seeping from various places), and I"m just not sure what to do.

Should I continue driving the thing until it dies, or should I start replacing things?

I'm getting married soon, so I don't have a lot of money right now, but I'd like to keep my cruiser happy.

Any thoughts, or suggestions?
 
what i found when my cruiser wasnt running right was well...alot of things, but mine wouldnt run without choke on either, the PO had disconnected the wire that comes from the carb and keeps it idling...without that it wont idle at all...there should be a black wire comming off your carb make sure its hooked up...maybe somone with more knowlege will pipe up and actually say where this wire goes to, i just connected the one from the carb to a black one comming out of my firewall and it worked....
 
if you flipped your bezel (back the way it should be) the cruiser gods might smile down on you and she might run better :flipoff2:
 
if it were only that easy!
that's actually an old avitor, I've fixed the bezel problem.
There is a green wire that has been disconnected - the wire is coming from the carb, but I don't know where it would plug into?
 
Green wire

wire from carb should be connected to switched 12V... that may help the idling issue.
 
On my 71, the idle solenoid wire is connected to the + side of the coil.

Good luck!

Do this and she will run great..... Ive seen me do it...
 
If I connect that wire to the coil(+), will I be in danger of shorting anything out on the carb?

I have also a question about the secondaries within the carb. Tonight I drove it around a little, had to get some gas, and wanted to warm er' up as it's quite cold up here in the NWT (North West Territories). When I took the choke off while driving, it began to spit and cough, if I pushed in the accelerator it sputtered and died. This does not happen if the choke is on though...Could this be related to the idle solenoid not being connected to 12v power? Or could this be the secondaries all screwed up? When I overhauled the carb, I could not use the new secondaries that came with the kit, because they were too different from the originals. I did clean them up real good though before putting everything back together.

And yeah, when I took it apart, I cleaned everything, replaced the parts that I could, (accelerator pump/gaskets), and put it back together.

I just want it to run well dammit!
 
If I connect that wire to the coil(+), will I be in danger of shorting anything out on the carb?

NO! There are two wires on a early 70s solenoid. The first is a short ground wire that should have a round eylelet on it and be attached to the choke cable tensioner bracket [which is held by the same two screws the solenoid is attached with.] The second wire is the power lead, which you can hook up to coil + without issue.

I have also a question about the secondaries within the carb. Tonight I drove it around a little, had to get some gas, and wanted to warm er' up as it's quite cold up here in the NWT (North West Territories). When I took the choke off while driving, it began to spit and cough, if I pushed in the accelerator it sputtered and died. This does not happen if the choke is on though...Could this be related to the idle solenoid not being connected to 12v power? Or could this be the secondaries all screwed up? When I overhauled the carb, I could not use the new secondaries that came with the kit, because they were too different from the originals. I did clean them up real good though before putting everything back together.

And yeah, when I took it apart, I cleaned everything, replaced the parts that I could, (accelerator pump/gaskets), and put it back together.

I just want it to run well dammit!

As far as the secondaries go, if you cleaned your old parts up well, there shouldn't be an issue with reusing them AS LONG AS THEY WERE THE RIGHT ONES TO BEGIN WITH! Unfortunately, that is too commonly an issue. I just finished rebuilding a carb for brandxmanagement here on the board that had a jet replaced with one almost 20% larger than stock!:eek:

Rather than 'fishing' for more possibilities, just go hook up the wire and then come back on the board and report on the results.

:)

Best

Mark A.
 
it might be possible for the fuel pump to leak into the block but I would think it would be also be leaking out of the weep hole in the underside if the diaphragm was shot.
I think I would change oil and filter and keep an eye on it
 
Connected the wire, seems to have the problem fixed.
However, I noticed that the oil has a strong gas smell, and appears to be quite thin.

Would anyone know why there would be gas in the oil?

Assuming you had to run around with your choke open for the truck to idle its prolly safe to say some gas did not get burned and ended up in the engine compartment.

Change Erl ASAP...
 
Would anyone know why there would be gas in the oil?


Other than choking, the other, more common reason for gas in the oil is a ruptured fuel pump diaphragm.
 
Back
Top Bottom