Painting question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 4, 2011
Threads
307
Messages
1,517
Location
Sacramento, CA
I am doing some touch up paint work to my rig and have a question.

I purchased all my supplies from a auto paint place and have painted parts before. However, today I ran into a snag right before I went to lay down my 2k clear coat (rattle can). I got up early after prepping last night, laid down my base paint coats this morning, and just as I was about to put on my clear coat in my driveway, my neighbor decides to work in his front yard. I am wearing a respirator but I chose not to lay down the clear because he was too close and I hear its not a good idea to breath that stuff. I drove it back in the garage.

So now my rig is sitting with the base coat on in the garage but with no clear coat. My question is, can I just go ahead and lay down the clear tomorrow morning, or do I have to lay down another base coat allowing it to flash off before I add the clear?

Thanks!
 
I'd hit it with some 600 before I sprayed it. I'm not a expert though, if you haven't tried this Spray Max stuff might want to. It's bad ass! I let the parts dry good scuff with 600 1 tack coat 2 medium wet coats 10-15 min between coats. Just reread your post, I would check to see what the paint people say for sure. WEAR PPE!
DSCN0997.webp
 
Last edited:
I'd hit it with some 600 before I sprayed it. I'm not a expert though, if you haven't tried this Spray Max stuff might want to. It's bad ass! I let the parts dry good scuff with 600 1 tack coat 2 medium wet coats 10-15 min between coats. Just reread your post, I would check to see what the paint people say for sure. WEAR PPE! View attachment 1480414

Yup. That's the clear I use. It's amazing stuff! I'm thinking 600 as well. I will probably lay down one more coat of paint, let it flash for 30 before applying the clear. I use the Spraymax base coat as well. Great stuff! Thanks!
 
Yup. That's the clear I use. It's amazing stuff! I'm thinking 600 as well. I will probably lay down one more coat of paint, let it flash for 30 before applying the clear. I use the Spraymax base coat as well. Great stuff! Thanks!

No need to guess at what to do. Just read the tech sheets for the paint.

Paint has instructions. It's important to follow them.
 
Every parking lots has examples of peeling clear or even base coming off, sometimes due to extending the window between coats.
Light rub down with 800 followed by light soap and thorough rinse has worked well several times for me.
 
....or you could just read the product tech sheets and follow the recoat window guidelines.

I dont think you understoo
....or you could just read the product tech sheets and follow the recoat window guidelines.

Let me explain a little further. There is a window (past flash) that is an ideal time to lay down a 2k clear coat (15-30min to ??? depending on ambient temp). Past this time, the clear coat doesnt bond with the topcoat, thus creating a laminate type coating instead of a chemically bonded coating. The can or the manufacturer website do not specify that window.

So my question is simple for someone who knows car paint, but not so simple for the average joe (you and me). Is there a window that closes that would require me to base coat again? I have read painters lightly sanding with 800grit paper, cleaning with a grease and wax remover, and then applying clear. Is this another option?
 
I dont think you understoo


Let me explain a little further. There is a window (past flash) that is an ideal time to lay down a 2k clear coat (15-30min to ??? depending on ambient temp). Past this time, the clear coat doesnt bond with the topcoat, thus creating a laminate type coating instead of a chemically bonded coating. The can or the manufacturer website do not specify that window.

So my question is simple for someone who knows car paint, but not so simple for the average joe (you and me). Is there a window that closes that would require me to base coat again? I have read painters lightly sanding with 800grit paper, cleaning with a grease and wax remover, and then applying clear. Is this another option?


Trust me - I understand coatings better than your average joe. You need to read the product tech sheets for your base coat and find out what the recoat window is. It's just that simple.

If your manufacturer won't provide that information, you need to find another manufacturer next time.

The manufacturers are very conservative with their recoat window specs. If they say it should be topcoated within 72 hours, it's perfectly OK to topcoat in 71 hours without worrying about adhesion issues.


If you're that worried, you can scuff and reapply some base and then clear. Most bases can be cleared up to 24 hours later.

Also, I wouldn't just scuff with 600 and then clear. I've seen some bad sanding marks show through with 600 straight to clear. It'll be ok to scuff with 600, reapply base, and then clear.
 
Last edited:
I have learned a ton from posts from @Splangy, you need to check the tech sheets for the base coat. That is the one that you need to check to make sure it is still in the recoat window.

Dude knows his s***.
 
He's got no tech sheet for the 1K. Vendor is closed for weekend.

I'm guessing you got a few layers of base down. If are able to wetsand tomorrow with 600-800 and are happy with how the base looks, I'd consider just coating your dried/scuffed 1k base with the 2K Glamour. Obviously, if sanding takes away too much base you'll need to add some.

:cheers:
 
He's got no tech sheet for the 1K. Vendor is closed for weekend.

I'm guessing you got a few layers of base down. If are able to wetsand tomorrow with 600-800 and are happy with how the base looks, I'd consider just coating your dried/scuffed 1k base with the 2K Glamour. Obviously, if sanding takes away too much base you'll need to add some.

:cheers:

Good call. Thanks, Dude.

Maybe it was a blessing in disguise because i noticed some dust particles in the base. I am going to remove those, then scuff down with 800, wipe down with grease and wax remover, tack cloth it, add 1 more layer of base coat, tack cloth again , and then clear it.

It's been over 100 degrees here so I will just do it early. I took some good pictures but my phone fell of my rig and is completely gone. The backup wasnt working so I have 3 years of resto photos down the drain.
 
I have used the same product-wear your PPE
 
Back
Top Bottom