OME Lift - Shackle angles

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 4, 2018
Threads
39
Messages
155
Location
Austin, Texas
Hey guys,

So i've had my OME 2.5" lift installed for a week or more. I just noticed that the shackle angles are different in the rear, will these settle out and be the same eventually - is this normal? I assume its because of the tire carrier and me sitting in it causing that side to settle faster. The space/gap between top of the tire and rear fender is also expectedly different on each side because of this. Took some pics of the shackles...

IMG-1965.webp


IMG-1966.webp
 
Or do I need to manually adjust the shackles to be the same? They were the same when I put the lift and and seem to have settled this way.

Any thoughts?
 
I had some early OME's and the shackle angles where always bad. Don't wait for that bad one to cam over on you. You'll bend your main leaf. They take for every to sag too. I would just take them off and reinstall them with good angles
 
Make sure the shackle bolts are not over tightened. Articulate the rear end and compress the passenger rear by driving the one wheel up on a block or ramp. Let it sit this way while parked for days or weeks. Consider swapping springs left for right. CCOT offers a shim that mounts between the spring and axle to fix 'cruiser lean'. Other than lengthening/flattening the spring, the only other way to improve shackle angle is to move rear shackle hangers forward.
 
Drive it with heavy stuff and or friends on the right side for some time just to see if it make it settle
I’ll probably try this first as well as making sure the shackle bolts aren’t over tightened on that side. Other threads say that these take a bit to settle but I am scratching my head on the one sided settle.
 
I had some early OME's and the shackle angles where always bad. Don't wait for that bad one to cam over on you. You'll bend your main leaf. They take for every to sag too. I would just take them off and reinstall them with good angles
Weird thing is that they we’re installed at the same angle originally. Definitely have adjusted on their own this way
 
I think I’d measure the spring lengths to confirm that one is settling more than the other. Plumb bob to the ground then measure between marks works good for this.
 
I think I’d measure the spring lengths to confirm that one is settling more than the other. Plumb bob to the ground then measure between marks works good for this.
Good thinking, what exactly should I be measuring? What is point a and what is point b?
 
You could get a ratchet strap and suck your rear end down to where the springs are getting flat. If you have good shackle angles then, you will be good when your springs settle in.
When I did this my shackle's where basically vertical when flattened the springs out. Your ride will be much better if you have angles around 30 degrees off of 90. I think the OME's are just to short. Thats why so many people have to rely on those anti cam over shackles and the rear end is so stiff your teeth rattle. All it takes is one speed bump and those verticle shackles will cam over. I've been there, 2 or 3 times. I bent my main leaf on the second time, and it was with the anti cam over shackles. I ended up moving the shackle hanger forward 1/2 to 3/4" got my 30 degrees and the difference was nite and day. I even put the short leaf I removed from the spring pack back in.🆒
 
Just discovered a new issue. Upon further inspection, I see that there are 2 different length shackles by .5 inches or so... I assume one set for the rear and one for the front. I thought these were all 4 the same as I didn't pay attention when unpacking. Anyone know if the longer shackles go in the rear or the front?
 
Good thinking, what exactly should I be measuring? What is point a and what is point b?
Here's how I measure them since it's just a comparison. But now, you're discovery sounds like it may be the issue.
I can see now in your pics the difference in shackle length and would make sense that the longer one on the drivers side is putting more load on that spring.
Don't know which ones go where but I'm guessing it's optional and would let you control how you'd like the rig to sit.
Iter

1903832
 
Just discovered a new issue. Upon further inspection, I see that there are 2 different length shackles by .5 inches or so... I assume one set for the rear and one for the front. I thought these were all 4 the same as I didn't pay attention when unpacking. Anyone know if the longer shackles go in the rear or the front?

I thought they were all supposed to be the same length. Where did you get this lift kit? I'd call them to see WTF is up with this.
 
Who did the install? For future reference, the bolts are not supposed to be torqued down until the full weight of the vehicle is on the ground.

If you haven't done it yet, I'd check the other corners too.
 
I’m a bit curious on the bolt torque as well. My shackles don’t look like yours, they’re from SOR, but when they are torqued down (bottomed) the shackles still rotate albeit with some restriction from the new inserts. Are your shackles actually able to pinch the springs?
 
Last edited:
Back
Top Bottom