they make 37's and 38's in the radials and 37's in bias.
http://www.pitbulltires.com/downloads/PBSPEC2.pdf
Official 37" and up picture thread (5 Viewers)
- Thread starter slow91fj90
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
they make 37's and 38's in the radials and 37's in bias.
http://www.pitbulltires.com/downloads/PBSPEC2.pdf
they make 37's and 38's in the radials and 37's in bias.
http://www.pitbulltires.com/downloads/PBSPEC2.pdf
Sorry I should have been more specific. I meant the radial. And although they do list a 37x12.5x16 they don't make it yet. That's why they don't have any of the specifications listed for that size.
Should have gone 37's a long time ago. It's rather "natural" on an 80. Doesn't look "moster truck-ish" like my old 4runner with 35's. No looking back here!
Last edited:
RockJock82
Sometimes you have to kick a little A$$
Did you make the front bumper? Looks pretty nice
Finally finished the installation on my '97 80. 4.88 gears, Aussie front, Spartan rear, Marks part-time 4wd kit, IronMan 6 inch lift, etc. I got the Nitto 37x13.50R20 used tires and wheels on Craigs list. So they are pretty worn, but cheap. It makes my old '83 pickup look pretty small
If you are going to wheel this rig, you're gonna want to have more rubber than rim. $hitcan those 20s and go 17s.
I think those look good, but we dont have rock fields to wheel here, usually muddy trails and bouncing along creek beds for hours.
Ive got the same tire on 17s.
Should have gone 37's a long time ago. It's rather "natural" on an 80. Doesn't look "moster truck-ish" like my old 4runner with 35's. No looking back here!
Hey Akarilo,
This is the first time I have seen your new FJC rims blacked-out, looks great! Do you have a better side shot that show them?
Thanks,
Derrick
itbrokeagain
SILVER Star
Just replaced my 37 boggers with 37 nitto mud grapplers. The nittos are a good 2 inches taller.
X2 , its unique too.
Thought that was Creepersleeper's rig at first glance. Nice body work!
itbrokeagain
SILVER Star
Yes I did, thank you. I built the front, rear, sliders, and skids protecting everything that is necessary on the underside. As well as a 23 gallon aux gas tank that sits where the spare was. We spend thousands of miles a year in the desert and it never let's us down. You can view some of my other posts to get better views of the bumpers
Phil
Phil
Should have gone 37's a long time ago. It's rather "natural" on an 80. Doesn't look "moster truck-ish" like my old 4runner with 35's. No looking back here!
what are your suspension specs? Rig looks perfect
its not quite done yet, but a set of 42 iroks are going under it.
Land Speeder
InstaH8R
14bolt steering front? Dana60 go boom!
RockJock82
Sometimes you have to kick a little A$$
Nah if your going through that much trouble a true high 9 with 40 spline inner/outers
14 bolt front would be money! True high 9 would be nice too. But Wouldnt a mildly built dana 60 be the cheapest option? id think it would hold up fine with 42's and the stock motor if you didnt beat on it? Didnt the shortbus run 40's with longs and chromo inners? They beat it up pretty good and it seemed to fair ok?
its not quite done yet, but a set of 42 iroks are going under it.
You have a build thread anywhere in the interweb?
