My Tranny update thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Union was clear when I reattached the hard line...so I am guessing whatever was in there has now been pushed downstream...but where is that?? Wish I had so idea where the return side dumped out??

Oh well guess I am really no closer to solving this than I was a few months ago..next ???
 
Any help you can offer would be greatly appreciated at this point....I just don't know where the next step is...I want to get back under it and try putting a section of hard line between the two soft lines and see if it flows without tyhe cooler but am thinking that wont be till Monday.

So any and all ideas are welcome..

Thanks
 
All the lines have been replaced and the I have wated to give up so many times but when the I drive the truck short distances it shifts so well and is so fun to drive I get remotivated to fix it..
 
I am sorry. I do not have a hydraulic circuit diagram anywhere for an Aisin trans of any type.
I have, however, found a couple of flow diagrams for domestic trannies. And my memory is wrong.
Return fluid from the cooler dumps straight to the pan. The filter is on the intake side.
What I am remembering is a Chrysler FWD transaxle that happens to filter the returning fluid, rather than the fluid entering the pump. Which is odd. And why it stuck in my memory.
There is a pressure releif valve which dumps fluid straight back to the pan after the pump.
I wish I could be more help, but this is a true mystery.
 
Just want to say thanks for looking and guess the pan will drop on Monday unless I learn something else..Dont really have any other ideas... guess it wont hurt...see whats in there and look at he filter
 
Ok a bump for anybody with ideas...gonna drop the pan tommorow or tuseday...still dont have any other ideas but will check the filter and see what I see...
 
Just to get this straight, you have great flow out of the tranny when the lines are not attached and none when they are attached?

Have you tried emailing or calling Rodney at wholesale automatics in Australia and asking for his opinion?
 
Just to get this straight, you have great flow out of the tranny when the lines are not attached and none when they are attached? Yes get great flow outta the tranny and outta the cooler but when the return is hooked up get no flow

Have you tried emailing or calling Rodney at wholesale automatics in Australia and asking for his opinion?
Yes have spoken with him and he really is as puzzled as I am
 
Ok a bump for anybody with ideas...gonna drop the pan tommorow or tuseday...still dont have any other ideas but will check the filter and see what I see...
I think the only things you can do next that make any sense are drop the pan and blow down a pipe into the return union to gauge if there's a restriction. If there is then blow some compressed air down the tube and see if you can identify where it comes out and if it's something you can take off for servicing or blow back through ...
 
Jon and everyone else I just want to say thnaks for the ideas...gonna get my supplies today and drop it tommorow...don't worry not driving it today :):)

Will post back what I find...can't believe what a project this has become....
 
...can't believe what a project this has become....

But just think what a sense of accomplishment youl have when you finally do figger it out. :)
 
Okay now I have a new theory and maybe someone else has an idea too...so chime in..I will beat this problem someday..I am thinking maybe the breather is clogged..cause if I leave the out put side of the cooler unplugged it is fine, close up the system and it acts like there is pressure in the system..

It leaks fluid ( I have cleaned up the pan and crossmember gone for a drive and fluid on it) and generally acts like a diff that is stuffed up...I unplugged the breather from the dipstick but cant figure out how to do the same from the tranny...any ideas?? cause i got some fluid outta the breather hose...

https://forum.ih8mud.com/80-series-tech/246532-94-transmission-vent.html
 
If you leave the output side of the cooler unplugged doesn't it just spew ATF everywhere?

Did you try blowing into the return union to check for resistance?
 
Jon,

It does spew fluid if I leave the output line off the cooler but I run it into a bucket. I haven't had a chance to blow into the input line yet because I haven't dropped the pan...caught a cold and wasn't up to the task.

I will try again in a week or so...just wondering if the tranny vent line would make a difference if it was blocked or not??? Thanks
 
It should be able to vent through the dipstick tube if the vent line is plugged. Try your tests with the dipstick removed and see what happens.
 
I tried it iddeling....guess I need to try driving it now, with no dip stick...also still need to try blowing through the iline that comes outta the cooler and goes into the tranny...this project never seems to end..someday I will win...at least that is waht I keep telling myself :):)
 
I will win, I will win is what I keep telling myself. I am sitting in Sedona Arizona right now but will be back on the project next Monday I hope... Will update then...
 
Back
Top Bottom