My Tranny update thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I am done..... it has beat me...thanks guys for all your help and ideas...I can't do it anymore...hours and hours and nothing...the truck will sit for a while until I decide what is next...
 
After some much needed sleep and a great hom,e cooked meal I have given this some more thought....

I get good flow when tranny pumps outta the union...no flow through the hardlines...but get brake cleaner through them...so that confuses me..

so back to believin the hard lines are my issue...so gotta solve that...now just gotta figure out where to start...cause they don't want to come out of the truck...
 
so back to believin the hard lines are my issue...so gotta solve that...now just gotta figure out where to start...cause they don't want to come out of the truck...
Are they free but not enough space to wiggle them out or are you having trouble getting them free even?
 
Are they free but not enough space to wiggle them out or are you having trouble getting them free even?

I can get them free and wiggling around but with all the bends can't get them free from the truck. I can't get the tranny low enough to bend them in a direction to allow them to come out.

As for blowing them out, blew them out with air, pushed wire as far as I could maybe 3 to for feet from the front end and maybe 2 feet at most from the back. I also sprayed a bunch of brake cleaner into the lines and blew it with compressed air, that came out but no blockage. So wondering if the lines are to blame or if the pump just doesn't have enough pressure to pump the fluid....but I do get approxiamately a gallon of fluid at 2000rpms staright out the side of the tranny.

just very frustrating I is all I can say...cause it shifts well and doesn't seem to slip or have any other issues...

Thanks keep the ideas flowing...i am sure I will have something to share someday...
 
If each segment is clear, then the whole thing is clear. Do a flow test right at the spot it goes back into the tranny. If there is no flow, go back one segment.

The two most likely places for problems are the cooler itself, and the line that flows through the radiator bottom tank.

Since this has become such a nightmare for you, why not just run a new external large cooler and be done with it?

One last test-can you access the hard line right where it comes out the side of the tranny? Put your compressed air there and see if it will blow through to the place where it flows back into the tranny.

My understanding of automatics is incomplete, but if there is enough hydraulic pressure to keep it in gear and let it shift, your pump is fine.
 
My understanding of automatics is incomplete, but if there is enough hydraulic pressure to keep it in gear and let it shift, your pump is fine.

This is a correct assumption.
 
Are the two hard lines free of each other so you can wiggle them seperately? My memory is a bit vague on this but I seem to remember there being some clamps that hold both pipes but don't bolt to anything if that makes any kind of sense! Just thinking that one pipe is easier to wiggle than 2.

IMHO the tranny is pumping just fine based on your gallon a minute test and the fact it is otherwise working well. If nothing is coming out the other end of the hard lines (with both disconnected just to be sure?:D) there must be a restriction in the hard line. I'm still wondering if the tranny has been out for a rebuild and when it went back in they screwed up the hard line(s) because it's a PITA to get back in.

Are there any cable, pipes, filler tube etc that could be removed to give more wiggle room in the engine bay? You know there's a throttle position sensor cable in the mix there somewhere that might be fowling your wiggling? I don't know how easy that is to disconnect at the engine end on a petrol 80 though.

It doesn't sound like clearing the existing hard lines is going to work. Have you priced up replacements? Maybe offering up a new hard line would show a way to wiggle it in and therefore a way to wiggle the old ones out? You may be able to take a slightly different route with the new lines and cut the old ones out ...
 
I guess what is the most frustrating is the tranny flows fine with no lines attached...then with lines attached nothing comes out the end of the hard line...so I take the hard line out of the union and it flows fine,,,,

I pump compressed air through the lines no problem and then spray brake cleaner down the lines it also comes out the other end...but no atf...it just makes me want to break something...

Guess I will play with it again weds or thurs....wish me luck...
 
Based on all of your test and cleaning process diagnosis, believe there is a place where the hard line it's hard bend maybe hit by something and get a heavy flow restrict .. un a outher line and end with this nightmare ..
 
Blowing compressed air down the hard lines might be a bit misleading because the air will be under much higher pressure than the ATF would be. A crimped pipe might effectively block ATF but allow compressed air through. A better but less pleasant test would be blowing down the pipe with your mouth and it should take no effort IMHO, like blowing through any other bits of pipe of similar bore that you might have to hand for a comparison?

I understand your frustration level, I went round and round trying to fix my lockup problem, but I did eventually sort it out ...
 
I got a nice and small tubing cutter this morning...after some sleep I might see if I can cut the hard line and get it out in 2 pieces...if I don't get to it this afternoon tommorow is my first day off so will give it a shot then....
 
Hello,
If you have not cut your line yet I would like to suggest that you turn your air compressor out put down to 20-30 PSI and then try to blow air through the line. If the air moves through the line then try to blow a plug through the line. I use a piece of a foam ear plug. If the plug does not come through then increase the pressure and blow it back out the opposite end of the line.
hope this help,
Gavin
 
Sounds like a good plan and I will give it a shot tommorow...I have gotten caught up in all sorts of other little projcets around the house and havent even looked at the truck in a week or so...
 
Started a new thread looking for tranny cooler hose size...chopped out all the hard lines and seems to be flowing through the cooler that I have temporaly mounted to the tranny....

Will replumb the whole system this weekend hopfully with rubber lines and really put it to the test.

https://forum.ih8mud.com/80-series-tech/243440-tranny-cooler-hose.html
 
Tim,

Go to a local hose shop and get some good -6 cloth covered steel braided hose and some new fittings for the trans and cooler. I use Orme bros. in Northridge, but there has to be a performance hose shop in the south bay area. I am not a big fan of rubber lines as they tend to get spongy after a while and can melt if exposed to high temps (exhaust).

Good Luck,

Dynosoar:zilla:
 
3/8 hose works, and you can reuse the fittings. The hose was some fancy stuff resistant to high temps and high pressure made by Earl's. $3 per foot.

I just did this to mount a cooler on the front of my FJ62.
 
Earls is good cause it is like a 10 minute drive but also gonna look into Russell cause I got a budy there....this weekends goal is rig it up with some clear hose and confirm proper flow....then do it right with good hose and drop the pan...new fluid and drive the hell outta the truck
 
Back at it again today...good times..as usual, well I think now what my issue is low line pressure.

I need to find somewhere to havet he line pressure tested. I have come to this concluison based on runing clear hose out of the tranny to the cooler, then a clear line outta the cooler to a bucket,. Start the truck up and get great flow outta the cooler and into the bucket. Now if I hook the return line up also with clear hose I get very limited to no flow. It builds up on the in line but does not push fluid in a circle, ie through the cooler to the tranny pan and back through the lines..

So what would it hurt to drop the pan and blow air or some thing else through the the return union?? To see if the blockage is there?? Or what else might my issue be??
 
I've not seen any kind of flow diagram to know what route the fluid takes from the case union. If there's some crud then it's already been pushed into someplace bad by hydraulic pressure or you wouldn't have a problem now. How likely is it that using some air will put you in a worse spot? Can you just try blowing down some pipe connected to the union yourself to gauge flow? I would expect there to be little or no resistance and is at least a low pressure test ...

Maybe the union itself has as blockage.
 
Back
Top Bottom