My Rolled 80

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

exo is a weaker design but will protect the body in a light roll. I suggested a internal since your body is already messed up and the fact the internal is much much stronger.

Agreed. Another point to mention, the COG will be lower and closer to center with an interior cage. I will be doing an internal cage in mine, but my :princess: wants an exo on hers... :rolleyes:
 
Sam - I feel for you. Those are scary moments. I did the same thing in 2002 in Pismo with 3 other guys in the car. I was driving up a dune at nite and started to turn out of it too soon once I got to the top and rolled three times on the way down and ended up upside down. It was pretty eerie to be out there, completely black, the engine cut, a track from Tool's Lateralus blasting and the headlights lighting up the next dune over. We were all fine though one guy in the back did not have his seat belt on so he moved around a bit. Every inch of sheetmetal was wrinkled and the truck was full of sand.

The rollover was pretty slow as I imagine yours was. I can't imagine what it's like to rollover at high speeds. We pushed it back over that nite and had a tow truck come get it the next day. I never saw it again. The insurance agent came to look at it a few days later and they ended up totaling it and sending me a check. This was 2002 with a low mileage 1997 LC. Then, it was on the hairy edge of being totaled. My wife put me in the penalty box for a year before I could go out and buy another.;p

Good luck!

:cheers:
 
I rolled in a '93 minitruck out in Wyoming...we were coming out of the being in the woods all day and my buddy was driving...he had the cruise set on 75 (speed limit on rural highways are 65) and I was sleeping.



so was the driver ;) - we ended up going off to the left and went into the ditch proceeding on to hitting a driveway embankment. We flew about 40 feet in the air and did a quick 3/4 roll ending up on the drivers door. That happened real quick to the point that I can't remember a whole lot of it. I almost think a slow roll would be worse because of the helpless feeling.

Glad everyone is okay - On the brighter side...chicks dig body damage. :grinpimp:


bk
-the virginia dude who knew beno preroll ;)
 
I'm getting my feel bads all hurt here,
I was the first ass hole to roll an 80 that I know of, That was back in spring of 2002 on Moab rim trail, Y'all are just followers........;)

Dave

P.S. Have you seen the unbreakable fab 80 overhaul in the hardcore section??
 
The rollover was pretty slow as I imagine yours was. I can't imagine what it's like to rollover at high speeds.

Well let me tell you, it's fast with very hard impacts. My senior year my buddy had me & my GF in his CRX, I was in the back where there isn't even a seat where I laid across with my knees up and we went off the road into the desert at about 70 mph where the CHP guessed we did 11 flips with a few of those totally air born. Your feet still come over your head and dirt and glass fly into your face and it's all over in seconds. We all had a body part go out a window but luckily we were all OK with the exception of my GF who got a concussion from hitting her head behind the ear on the window frame. But that could have been deadly if the car would have landed on her head.
I must say to you Sam that when you survive a roll over unscathed you kinda get a in-explainable confidence that you can survive any accident that you happen to be in. So be careful because that's probably why my buddy totaled his 95 mustang a couple of years later.
 
Now that's classic bk....

;)

BTW, what is the latest with you rig Onur? I remember following the thread earlier in the year but can't remember seeing any updates.

Smit
 
I guess the guys at LINK will have a new pony in their stable pretty soon huh?
Smit
you had to bring link up..... ummm I think sammy would be better off buying a 220V welder and a tube bender, and i will help him build a cage/back half 80.
I guess I am missing something Ian. Hope I did not offend anyone. If there is a story, I promise I don't know it.
Only thing that I can speak on LINK about is that they cut some 1/4'' steel plates in half for me one day. Only took 30 seconds and they did not charge me.
Smit

TO all that I will say this: As pple the Link guys are cool and very nice, BUT unfortunately they will not see my truck again. This is a decision strictly made on business/quality terms based on severly bent sliders, broken rear shock mounts, and a broken Hi/low shifter link. Others experience maybe different I can only speak for myself...I would hope that their desert trucks do not encompass such qualities.

I wish I only had good things to say, but I give the truth, and if it's not sunshine and cupcakes then so be it. I give everyone a chance to correct their wrongs.

Sam and I had the opportunity to talk at length Saturday and Sunday. He's an amazingly mature young man that will go places, make something of his life and learn from this experience.

Sam - just tell your parents about all your 50 year old friends doing this and they may understand that it's something you will never grow out of!

Parents handled it quite well. As much as they don't agree with it, they do understand that it was paid for by myself so that gives me a little leverage.

I must say to you Sam that when you survive a roll over unscathed you kinda get a in-explainable confidence that you can survive any accident that you happen to be in. So be careful because that's probably why my buddy totaled his 95 mustang a couple of years later.

No in-explainable confidence here blue...I am humbled and grounded as deep as this earth will go. I've always respected the environment and nature and know that my truck is meerly a needle in a hay stack, this made me realize that i'm more of a grain of sand in the ocean.

To be perfectly honest...I have some fear of dunes at night time and my next time out there, I don't doubt that my trek into the night will be accompanied by sweaty palms and newb caution. Sadly we couldn't have been going 15 or so mph that was the last number I recall on the ole speedo.

You guys are truly therapy and I can honestly say all these comments have and continue to make this WAY easier and help me to see the light at the end of the tunnel. Thank you
 
Last edited:
TO all that I will say this: As pple the Link guys are cool and very nice, BUT unfortunately they will not see my truck again. This is a decision strictly made on business/quality terms based on severly bent sliders, broken rear shock mounts, and a broken Hi/low shifter link. Others experience maybe different I can only speak for myself...I would hope that their desert trucks do not encompass such qualities.

I wish I only had good things to say, but I give the truth, and if it's not sunshine and cupcakes then so be it. I give everyone a chance to correct their wrongs.

Sammy,

1st and foremost really sorry to hear of the roll. Glad to see that everyone walked away and you have a great perspective on how to move forward. I look forward to watching and reading what you decide to do with the rig. That said, I know I have been "outa the game a while" and I might not have a clear picture of what transposed with you and the boyz at the shop. But as a now outside observer, bent sliders on a rig that I'm sure weighs close to mine or more 6500+ with a body lift is not uncommon. Especially when those sliders are mild steal, has nothing to do with quality, its shear weight and abuse. Broken shock mounts... again, I'm sure we have all seen the Black Raven flyin last year 4 feet off the dune pic... Pigs as big as ours have no right to fly that high, and lastly shifter linkage... again body lift, flying 80, weight... There is a common thread here and it's not the shop that did the work. When you start to push your rig like you do... stuff will happen and things will break, bend and roll........That’s the name of the game, push it, break it rebuild it. Find me one HC wheeler who has not gone through the very same things you have. I think you will find that most have broken, bent, sheared much more and that speaks for what great rigs we have as a base platform.

To each there own, sorry you feel the way you do but it's no skin off my back as I sit here with the sun sand and a North Swell on its way.

ALOHA!!!!

-Ammo
 
Sammy,

1st and foremost really sorry to hear of the roll. Glad to see that everyone walked away and you have a great perspective on how to move forward. I look forward to watching and reading what you decide to do with the rig. That said, I know I have been "outa the game a while" and I might not have a clear picture of what transposed with you and the boyz at the shop. But as a now outside observer, bent sliders on a rig that I'm sure weighs close to mine or more 6500+ with a body lift is not uncommon. Especially when those sliders are mild steal, has nothing to do with quality, its shear weight and abuse. Broken shock mounts... again, I'm sure we have all seen the Black Raven flyin last year 4 feet off the dune pic... Pigs as big as ours have no right to fly that high, and lastly shifter linkage... again body lift, flying 80, weight... There is a common thread here and it's not the shop that did the work. When you start to push your rig like you do... stuff will happen and things will break, bend and roll........That’s the name of the game, push it, break it rebuild it. Find me one HC wheeler who has not gone through the very same things you have. I think you will find that most have broken, bent, sheared much more and that speaks for what great rigs we have as a base platform.

To each there own, sorry you feel the way you do but it's no skin off my back as I sit here with the sun sand and a North Swell on its way.

ALOHA!!!!

-Ammo

Yes, thank god everyone walked away. I know they are your boys and I have nothing against them personally, I think they are great peoples.

Just to clarify... I definitely agree that when you play you break...no problem, but sliders are not suppose to bend completely into the body of the truck on their first run out severly damaging the rockers. an inch or two here and there no problem, but major damage to the very part of the truck the sliders are suppose to protect by the the protection device? not right IMHO. Rear shock mounts failing at the welds on both sides. If I was in the Baja 500 I'd understand but we are talking 4 trips total over 1.5 years and change.

Extreme use probably, BUT that is why I paid Extreme cash for the build, granted full knowledge of what the truck is used for all 3 to 4 times a year if that. If this was a Prerunner and it saw such breakage...a WHOLE lot more would be at risk and that worries me.

Again, I know they are your buddies and I'll have a drink and shoot the s*** with them anyday, but I cannot let them work on my truck. I call them as I see them and I hope that anyone and everyone is satisfied with their work, but I was not. I wish could say otherwise and sing their praise b/c they are pretty people, but I can't. Maybe I'm the outlier in this equation.

Missed you this past weekend the recovery needed some desert camo pants and another "Wilee" in the dunes.:beer:
 
If I was in the Baja 500 I'd understand but we are talking 4 trips total over 1.5 years and change.

Extreme use probably, BUT that is why I paid Extreme cash for the build, granted full knowledge of what the truck is used for all 3 to 4 times a year if that. If this was a Prerunner and it saw such breakage...a WHOLE lot more would be at risk and that worries me.:


Sam,

Very cool, And my intent is not to turn this into a discussion of "You should love Link" and I respect your view and understand your concerns. But I just want you to think about what your expectations are. Granted you are entitled to them, and you have set them HIGH. Nothing wrong with that but that is what this comes down to right? Un-met expectations. The shop did not build you a race truck, period. They did some minor mods to your rig, that does not mean even 3 or 4 times a year you can launch a 6500lbs lead weight and not expect damage. A pre-runner weighs half that weight if that. They are built purpose intended, to go fast and suck up lots of travel and energy. And yes Pre- Runners break too, that’s part of the sport. Matt's Taco/ Tundy blew the 3rd 3x's because he wanted to keep the truck Toyota and run the tundy rear. Most guys run ford 9's. It's the name of the game.

Being a "Vendor" myself in a whole different venue I understand how a customer and there "expectations" can sometimes fall short. But it kills me when maybe on the front end; the real problem was communication in the pre sale of an item so the customer and the vendor understand the "expectations" that should be met and or the intended purpose.

Just my two cents and over 10yrs in sales.

The link shown below was not your trucks intended purpose, lets see how Kev makes out this weekend, his truck was built for this..

http://www.youtube.com/watch?v=GsFgasNBcP8

Again, not a huge debate, glad to see you are ok, Build It BETTA and learn from the breaks.

-Ammo
 
Last edited:
I am sorry to have even walked this thread down this path :frown:

Smit
 
I am sorry to have even walked this thread down this path :frown:

Smit


Smit,

It's not your fault... I just had to throw my 2 cents in. I will return under the rock and drop it like it's hot.

-Ammo
 
Last edited:
Sam,

Very cool, And my intent is not to turn this into a discussion of "You should love Link" and I respect your view and understand your concerns. But I just want you to think about what your expectations are. Granted you are entitled to them, and you have set them HIGH. Nothing wrong with that but that is what this comes down to right? Un-met expectations. The shop did not build you a race truck, period. They did some minor mods to your rig, that does not mean even 3 or 4 times a year you can launch a 6500lbs lead weight and not expect damage. A pre-runner weighs half that weight if that. They are built purpose intended, to go fast and suck up lots of travel and energy. And yes Pre- Runners break too, that’s part of the sport. Matt's Taco/ Tundy blew the 3rd 3x's because he wanted to keep the truck Toyota and run the tundy rear. Most guys run ford 9's. It's the name of the game.

Being a "Vendor" myself in a whole different venue I understand how a customer and there "expectations" can sometimes fall short. But it kills me when maybe on the front end; the real problem was communication in the pre sale of an item so the customer and the vendor understand the "expectations" that should be met and or the intended purpose.

Just my two cents and over 10yrs in sales.

The link shown below was not your trucks intended purpose, lets see how Kev makes out this weekend, his truck was built for this..

http://www.youtube.com/watch?v=GsFgasNBcP8

Again, not a huge debate, glad to see you are ok, Build It BETTA and learn from the breaks.

-Ammo

Smit it's fine you mentioned and I would have left it at my first statement, but what's right is right and I can't stand quietly by.

the two cents needs to make sense and the facts do not line up bro. There is a time to fight the fight and others to just say there was a mistake and hope that it would be corrected and not repeated for their own good.

No one is blaming anyone, who would place the rear end weight of a truck on, 1x3" radious bolts at a downward angle welded to the outside of the trucks stock mounts?

I would hope that the little that I ask of is not considered "race truck" quality and doubt anyone else would (a simple shock bucket mount would have eliminated the problem).

To have the expectation that my truck will not break down on the trail everytime is not a high expectation. And as far as jumping the truck I can count on 1 hand how many times that has happened since they did the work. They took the easy and quick way out when they did the rear lower mounts and that's fine, it still doesn't explain the sliders etc.

I've done all the talking I can... and all those who have seen the work in person can atest to what i've said.

Thanks again for the kind words from everyone... I love this board and everyone who's been so helpful and positive.
 
Sammy:

Very sorry to hear about your roll buddy… that sucks. You have never been easily on that rig, now it looks like a true trail rig. Pick one of our mags and I will get you in the back in the Woops section. It really does not look that bad. I like the idea of cutting off the roof, tube an internal cage/roof, new front fender and tube doors. You need to buy a reasonable daily driver anyway, gas is too expensive. Think of how sweet it is going to be when you can wheel without a care in the world of body damage. You are going to be able to attempt many new and different lines now that body damage is of no concern. Again buddy truly sorry about your rig but look forward to seeing what it will turn into.
 
Like most here, I am sorry to see/hear of your roll and carnage. :doh:
May I inject a bit of optimism? I bought my 80 from Brother Rob when it looked a lot like yours does now. The roof was down about 6", the front of the hood mashed, and the left side looked like a barn had hit it at high speed! The "A" pillars were collapsed and both "B" pillars bent. I still have ATF stains on the headliner! Otherwise, it looks great!
I repaired the rig without replacing a single bit of original metal. My repair parts list was; 1 windshield, 1 left door glass, 1 left mirror, 1 left taillight, 1 LF door handle. I shaved the flares and roof rack, (or rather Rob shaved them off, I just welded up the holes!) Look here for a thread called "Sunny Belly" for details and smartass comments. My truck is the John Deere Green 80 seen here and in the Prescott AZ area. PM for more advice.
 
Sam, we are a long way away, but I have a straight body if you need it. I will donate it to the cause. It is a 96 as well, so the swap should be relatively easy. However it is in Colorado, so you would have to get it to CA. The color is even close, It is the two tone green/gray. It even comes with some doors.
 
Back
Top Bottom