Local For Sale/Wanted Section!

[shmukster]

Someone needs to grab this!

Facebook

www.facebook.com

"bad engine"

$850


View attachment 2486007

If I had the room at my place I'd jump on this. I assume it's a 22RE engine. I've had a few of these old 4Runners and got my introduction to four wheeling in one they're awesome trucks.

 

[YotaFun]

Someone needs to grab this!

Facebook

www.facebook.com

"bad engine"

$850


View attachment 2486007

I wish I had the room! I even have a 3.4l I could drop in it!

 

[El Dahs]

Someone needs to grab this!

Facebook

www.facebook.com

"bad engine"

$850


View attachment 2486007

@Stairgod

 

[jamarquardt22]

The top alone is worth that.

 

[jtaco1]

Pretty sure I would end up divorced if I brought that home. That is a good deal and like Avi, I have an entire 3.4 setup that could go in it.

 

[YotaFun]

Pretty sure I would end up divorced if I brought that home. That is a good deal and like Avi, I have an entire 3.4 setup that could go in it.

That's my stance too, if I bring another vehicle home, I'm sleeping in it...

 

[JeepinPete]

I'm glad it sold. I have no need, but I really have a soft spot for those trucks.

 

[Crusha]

Great deal on a portable solar panel!

Rockpals 100W foldable Solar Panel - 64.99 +tax shipped

forum.ih8mud.com

 

[caz]

JD2 model 32 manual tubing bender - $150

Been "storing" this thing for years. I've decided I will never use it again.

It comes with a 1-1/2" die.

I'd like to get it out of my garage ASAP.

 

[jtaco1]

JD2 model 32 manual tubing bender - $150

Been "storing" this thing for years. I've decided I will never use it again.

It comes with a 1-1/2" die.

I'd like to get it out of my garage ASAP.

I'll take it. I'll be in Lancaster next weekend, the 21st, at Andy's and can pick it up. If need it out a bit sooner, I could swing by next Tuesday evening on my way back from Philly.

 

[JeepinPete]

Dang, 19 minutes too late. If JT changes his mind...

 

[jtaco1]

Dang, 19 minutes too late. If JT changes his mind...

I'm always willing to share

 

[caz]

I'll take it. I'll be in Lancaster next weekend, the 21st, at Andy's and can pick it up. If need it out a bit sooner, I could swing by next Tuesday evening on my way back from Philly.

Works for me!

 

[jamarquardt22]

Dang, 19 minutes too late. If JT changes his mind...

He won't. I won't let him.

 

[caz]

I have a kingpin single rear wheel Dana 60 FRONT axle I would like to rehome. It is a passenger drop, has no brakes, needs 35 spline outers, but has 35 spline inners and drive flanges. I don't recall the gear ratio, and the 3rd is probably toast from sitting outside for 10+ years without the axle shafts installed.

I'll sell for cheap. because it is not complete and because all of the parts are not there. I was thinking $150 for everything.

 

[jtaco1]

I have a kingpin single rear wheel Dana 60 FRONT axle I would like to rehome. It is a passenger drop, has no brakes, needs 35 spline outers, but has 35 spline inners and drive flanges. I don't recall the gear ratio, and the 3rd is probably toast from sitting outside for 10+ years without the axle shafts installed.

I'll sell for cheap. because it is not complete and because all of the parts are not there. I was thinking $150 for everything.

Have any pictures?

 

[caz]

I can get some - probably not until the weekend because it is outside and daylight is limited.

 

[jtaco1]

Not a problem. I can take a look at it when I get the bender from you. Thanks

 

[surfishjoe]

Part’s Matt gave me this radio installation kit at Fall Crawl. If anyone wants it it’s free.

 

[brian]

is that the corrola one?