its definitely the tcase

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 6, 2004
Threads
234
Messages
4,449
Location
Bozeman, MT
its definitely NOT the tcase

Ok so after lots of fun diagnostic tests its been decided that the problem is definitely in the t-case. With the side panel open we could see all the gears on the shaft from the tranny turning just fine. But somehome from one side of the t-case to the other this almost stops. The wheels just barely turn, so slow you can stop them with your foot. Does anyone know what could be causing this? Why the gears on the tranny input shaft would be spinning but on the other side theres little to no spinning.
 
Last edited:
Correction to my post it is definitely not the tcase because I restarted it and now the input shaft on the tranny isnt turning. So now I'm going back to clutch issues. Although I dont know why it would have been turning before I dropped the t-case and not after. And for the record it was definitely not in neutral so dont say that again.
 
I know I asked before but are you sure the input gear and PTO spacer are in correctly?
 
clemson55 said:
Correction to my post it is definitely not the tcase because I restarted it and now the input shaft on the tranny isnt turning. .

How do you know the tranny input shaft isn't turning? It isn't easy to see this without removing the shift lever cover or the clutch cover.

If the transfer case input gear is turning and the drive shaft isn't, then the transfer is in Neutral, or there is something seriously wrong with the case, like all the teeth are stripped off the gear or the output shaft has snapped. This is very unlikely.

Remember, things in the drive train can turn by friction when there is no load on it when the gears are in neutral.

Try holding the transfer case input gear still while turning the drive shaft. If you can turn the drive shaft without turning the gear, then the transfer is in N (or it is really F'ed up).

As far as I can tell from what you are writing, you haven't check anything yet in a meaningful sense before making the diagnosis. What I would like to see from you is something like:
" I grabbed the hi-lo shift arm and moved it and I could feel in click into all three positions when I turned it" or "I grabbed the trnsfer input gear and I tried turning the rear drive shaft and I couldn't turn it without turning the gear". Now that would mean something.

Guessing won't do.
 
Last edited:
I'm thinking it is in neutral. :flipoff2:








































And your clutch plate is backwards.
 
Pin_Head said:
How do you know the tranny input shaft isn't turning?

Perhaps he is looking at it using a fiberoptic scope through the oil fill hole.
 
Are you 100% CERTIAN that the clutch is working properly?



If the trans is in top gear, (3rd for three speed 4th for four speed) can you push the truck, and does the engine turn when you do this?


Have you removed the tin cover on the bottom of the flywheel housing and verified that the operation of the acctuation system?
 
clemson55 said:
Or maybe with the t-case off u can see it sticking out the back of the tranny and see if its turning when you put the cruiser into gear.

Umm, that would be the tranny OUTPUT shaft sticking out the back of the tranny. The tranny INPUT shaft sticks out the front. :flipoff2:

Maybe you are just being careless with your descriptions, but it is hard to help if we don't have an accurate picture of what is going on.
 
Sorry, the shaft does go into the t-case though so therefore it is also an input to some degree. However I'll correct that from now on.
Yes I did remove the cover off the bottom of the bellhousing and I can see the clutch fork depressing.
As for pushing it I have the cruiser up on stands because I already disconnected the driveshafts and took off the t-case.
 
clemson55 said:
Correction to my post it is definitely not the tcase because I restarted it and now the input shaft on the tranny isnt turning. So now I'm going back to clutch issues. Although I dont know why it would have been turning before I dropped the t-case and not after.

Assuming you are saying here that the OUTput shaft of the tranny was moving, but easily stopped, before you removed the transfer case, and then stopped moving entirely when you removed the transfer case, and assuming you are correct that the transmission input shaft is in fact turning, that can only mean that the transmission is in neutral.

When the clutch is engaged and the motor running, the transmission input shaft (1) will be turning. If things are balanced and there is no load, even in neutral the output shaft can spin a bit (friction despite grease), but you can grab and stop it easily. Removing the transfer case may put things out of balance enough that the output would stop.

If the shift fork (7) and (5) are installed incorrectly, or not at all, and do not engage the sliding gear/clutch hub, and it is in neutral position, that could give you such a situation.
trannytrans (Small).webp
 
Ok so if I pull the top off the tranny I can shift it manually and be certain it is not in neutral correct? if that is correct then how will I know for certain it is in a gear and not in neutral?
 
Yes, you can take off the transmission top and look down inside and see if the input shaft/main drive gear at the front turns when the engine turns over.

If it doesn't, then you know your clutch isn't engaged.

If it does, and the rear/output shaft is not moving, then you can look at the sliding gears and see what isn't engaging, and slide them back and forth with your fingers (engine off!) until you understand what is supposed to be happening.
 
Clemson55 - calm down.

Work this logically, don't assume anything.

Start writing things down, design experiments to test things, and, for crying out loud, use the FSM terminology to refer to things, so we can all be on the same page.

What do you know?

What don't you know?

What do you know that ain't necessarily so?

You've got a lot of smart people trying to help you here, so trust that they CAN help you.

STOP GUESSING, START DIAGNOSING.

Kirk
 
Pull the clutch cover off and check if the clutch disk is spinning at the same speec as the flywheel/pressure plate when the clutch pedal is up. If not, the clutch is not engaging. If you can shift the tranny normally, the chances of it being screwed up are pretty low. It seems very strange that the output shaft isn't spinning with the transfer case off. There should be enough friction or drag that it should spin any time the engine is running when the transfer case has been removed.
 
Do you have a 3 speed tranny or a 4 speed. If you have a three speed, and you removed the transfer case, you now have a tranny that is PERMANENTLY in Neutral! The transfer case retains the rear bearing for the tranny, and once it has moved back about 1/2 an inch, the output shaft is basically disconnected and the needle roller bearings in the imput shaft are just looking for the right moment to fall into your countergear cluster. :doh:

So I hope this is either a 4 speed, or another terminology problem.

:)
 
he has a 3spd tranny, so now that the t-case is off it will not spin the out-put shaft until the t-case is reinstalled? Also when you say permanently, do you mean even if we reinstall the t-case this will be the case?

Like Clem55 said when looking with the PTO cover off we could see the output shaft on the tranny spinning, and it would pick up RPMs with the gas applied but it was not transfering to the driveshafts. I understand the thoughts for the T-case in nuetral, but the first thing I did was shift the shifter on top of the T-case through its 3 positions with no change. Could the actual linkage inside the t-case be out of wack, becasue it shifts fine on top of the t-case fine.

We will check more closely with the clutch and its potential issues, I just have a feeling it isn't the issue here, but I will probally eat my words on this one:)

We appreciate all the help and input here guys, after class today we will give it another go
 
Back
Top Bottom