Hitch drop offset?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 7, 2006
Threads
11
Messages
39
Location
Aragon, Spain.
Hi! Anybody knows what's the drop offset of a factory Lexus Lx-450 ball mount hitch?
My rig came without it, and I don't know this.
The hitch looks like this:
...And the Part number is: 00214-90960 M96
mkj1.webp
 
As far as I know, the ball mount does not come with the vehicle. The drop of your hitch should be determined by the trailer you are towing. The trailer should be as level as possible. I have two hitches, on with no drop and one with two inches, so that I can cover the difference in size between my winter tires and summer tires and also the difference between the two boats I tow.
 
x2.

A fairly standard drop is 2". Looks like you are stock height, so as Bearcat80 stated, go with what you are towing and keep it level. Hitch and ball aren't that expensive.

With my lift and Kaymar, I use a 6" drop for our trailer.
 
I you plan on putting a receiver mount on your truck, you may want to look at other types like the Draw-Tite (IIRC) that does not have the 2" tube lower than the main mount frame. You save 2"+ of ground clearance that way...
 
Ummmm......Eric. Put your glasses on and look at the picture again. He already has the hitch and is asking about the ball mount. :flipoff2:
 
Ummmm......Eric. Put your glasses on and look at the picture again. He already has the hitch and is asking about the ball mount. :flipoff2:

I went by what he wrote... :)
 
The same as your trailer X2

What are you towing? / type of trailer?
My 80 came with the factory hitch ( I think it is a class III , 5000 lb )
I took it off pretty quick after I whent for a drive in the woods.
I put a pintle/ball hitch on (they were on sale the local Princess Auto outlet)

it bolted straight on........... and my 93s bumper is rated to tow a 3500 lb trailer according to the manual.

I think tou would find that an unlifted 80 with this hitch is pretty close to a "standard/average height trailer"

With the ball/reciever I have for the big hitch you can flip it over and re-mount the ball , it changes the height by about 3".

I also holed my stock bumper and flush mounted the 7pin plug for the brake controller.
 
Excuse my poor english. I wrote hitch, I meant Hitch receiver.

your english is fine, and I think I understood the question fine too. Brent OTOH... :D
 
Whoah, I didn't know the stock bumper with a pintle/ball could handle 3,500 lbs!!!! I am getting ready to make my first tow the last weekend in Jan and that is the only reason I have left my draw-tie on. I am renting a 24' pop-up for the trip and that may weigh over 3500 lbs but if it didn't I would luv to ditch the draw-tie for clearence.
 
your english is fine, and I think I understood the question fine too. Brent OTOH... :D

Why can't engineers just admit it when they're wrong! Don't just over analyze what's written - take in the whole picture if you get it! :flipoff2:
 
I think I understand what e9999 is saying. He's suggesting that there is an option to buy a receiver that only hangs down ~2" below the frame, rather than 4"+.

-Spike
 
Marlin,

Just curious about the stock bumper rating - is this actually in the manual, and if so what page?

DougM
 
Marlin,

Just curious about the stock bumper rating - is this actually in the manual, and if so what page?

DougM

Doug, is THIS what you are asking about?
 
Doug,

Fire trucks link reads the same as page 111, 112 of my 93 user manual.
 
Doug, is THIS what you are asking about?

well, not obvious what "package" means in there... could that be the cooler, harness etc not necessarily meaning the hitch receiver?
 
Paso, just so Brent can sleep well tonight, did I guess correctly that you don't have the hitch receiver yet and that the photo above is not your truck? :)
 
Well, as far as I know, every NA 80 series came with the towing package, which is a tranny cooler. The receiver hitch was optional. So that makes me wonder why they even mention towing w/out towing package. Not to muddy the water anymore... :doh:
 
Whenever I hear of folks talking about towing heavy loads off just the rear OEM bumper, I shudder. I tow a little trailer this way because I have a super stout steel Slee bumper, but the OEM structure is just NOT there to support a big tow load without reinforcement. To see this, all you have to do is lie down with a flashlight and look. Toyota steel is sure strong, but there isn't enough of it there, nor is it braced adequately for severe torsional loads.

BTW I believe that the "stock bumper rating" isn't what is indicated on that placard inside the door. Those are ratings for use with a frame mounted 2 inch receiver. I've never seen any published figure for towing off a bare factory bumper, because the Mother Ship doesn't want you to do it.

Toyota is really paranoid about towing. Their RAV4 hitch, for example, is waaay stouter than any aftermarket version, with extra gussets and four times as many bolts. It's a sign that they definitely want those loads carried properly, with good strees distribution to the structure. Whether it's the lawyers talking, or the engineers, it still makes sense.
 
Back
Top Bottom