head gasket help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 8, 2006
Threads
100
Messages
501
Location
Chadds ford, pa
Hello,

I installed a new head gasket and can't get a tight seal? I clean off the head and torqued it down to 90 ft lbs but it is dribbling fluid down the driverside block. I torqued them a second time after I warmed up the enigine and still can't get it to seal. What next?
 
hello,

First off you need to clarify some things; for instance, what year is your rig, what motor do you have, what info are you going by???
I've got a 71 one with an Fmotor and have the infamous "head gasket leak". It's common with the weak Fmotor valve cover. I've been recommend to switch out to an 2Fmotor valve cover with a rubber seal instead of the weak cork one and that should fix my leak. I have yet to do so but it's on my list. my prority right now is my transfer case so i'll get you that later on.
post some more info .......
 
ROOKIE TO ROOKIE
hahhaaaa>.......LOL
 
What was the original problem that you install a new head gasket? The head my be warped in my case I had to do resureface the block and the head befrore installing a new gasket. I hope this helps Good Luck.
 
Br sure that your head bolt holes in the block are CLEAN! if there is any crap or some oil or water in them? it can give you a false torque.. same for the bolts... clean them with a wire brush...apply a little oil to the threads when installing them... also check the dowels for a good fit.....
 
Br sure that your head bolt holes in the block are CLEAN! if there is any crap or some oil or water in them? it can give you a false torque.. same for the bolts... clean them with a wire brush...apply a little oil to the threads when installing them... also check the dowels for a good fit.....

My first thought too. Second thought:poor quality head gasket. Please tell me you didn't get one of those steel-faced head gaskets?:eek:
 
If the head has been cut... did you cut the locating rings in the corner head bolt holes?

Again, what engine, what mods/repairs/whatever. What fluid (coolant or oil)?


Mark...
 
Br sure that your head bolt holes in the block are CLEAN! if there is any crap or some oil or water in them? it can give you a false torque.. same for the bolts... clean them with a wire brush...apply a little oil to the threads when installing them... also check the dowels for a good fit.....

You need to chase all the block threads with a tap. You will be very surprise what comes out. Use antisieze on all the headbolts. Using a wire brush will not clean the threads like chasing them with a tap will. Without doing this, you will never get the correct torque on the headgasket.
 
You need to chase all the block threads with a tap. You will be very surprise what comes out. Use antisieze on all the headbolts. Using a wire brush will not clean the threads like chasing them with a tap will. Without doing this, you will never get the correct torque on the headgasket.

What size tap? tread pitch & bolt diameter?
 
What size tap? tread pitch & bolt diameter?

I just got my 3.0 liter V6 from the machine shop.
Here is the information my machinist gave me:

"So before we even think of going to maximum torque, we clean the threads in the block with a chaser, (NOT a tap)..Then we oil the threads and spin the bolt all the way in and out with our fingers. This assures they are clean and lubed.

Then we pull them to 50%, all of them. ... back off 1/4 turn and repeat, note each time it will turn a tad more before 50% is reached. This is because the threads are bedding in. We do this 5 times, then we go to 75%, then to 100%, all done. We do this with ALL new fastners...it assures a more even clamping force, inconsistant clamping force is the number 2 cause of early head gasket failure..(heat is number one)"


You can make a chaser. Take a head bolt and cut a notch in one side of it. Clean it up with a file.
 
The 3VEZ is a whole different dog... those head bolts are considered by many rebuilders as stretch-to-yield bolts ...that should only be used once.. The reason your machine shop is using that procedure is to stretch & relax..stretch& relax.. over and over to stretch them out and hope for the best....But when it comes down to it, once used, junk them, to have total piece of mind... that is if that sort of thing keeps you awake at nite?? It does me....
 
even on f motors just for the hell of it i always replace the head bolts.when tighting the head bolts i follow the tighting sequence but i first do 20 foot pounds then 50 foot pounds then the 90.sounds like your head may be warped.theblock deck warpage allowed limit is 6 thousands of a inch i believe:o .its been awhile.if you did not spend the 100 bucks or so to a shop to go over it .
 
Thanks for the responce. The engine is a 2f i used a cool cruisers aftermarket gasket. I guess I should get a toyota gastket and have the head surfaced and Maybe a new set of bolts. What Pita!!
 
The 3VEZ is a whole different dog... those head bolts are considered by many rebuilders as stretch-to-yield bolts ...that should only be used once.. The reason your machine shop is using that procedure is to stretch & relax..stretch& relax.. over and over to stretch them out and hope for the best....But when it comes down to it, once used, junk them, to have total piece of mind... that is if that sort of thing keeps you awake at nite?? It does me....

The machine shop that built my motor does this on ALL of their blocks.
From 100hp Honda's, to 1500 hp Big Blocks.
 
Anyway after all this, still no answer about the tap or thread chaser size for the 2F? who cares about a 3.0?
 
Anyway after all this, still no answer about the tap or thread chaser size for the 2F? who cares about a 3.0?

Re-read my first post.

Specifically, the last line.

A new head bolt will cost you less than a good thread tap, or thread chaser.
 
Hello,

I installed a new head gasket and can't get a tight seal? I clean off the head and torqued it down to 90 ft lbs but it is dribbling fluid down the driverside block. I torqued them a second time after I warmed up the enigine and still can't get it to seal. What next?

Is the head warped???

Have you checked?

Why was the head pulled in the first place?

Block, warped? have you checked?

Those jump out at me as culprits....
 
Head gasket

Hello thanks again to all. I have not checked for a warped head or block. how can I check this?
 
Back
Top Bottom