Having problems with stearing controal on acceleration

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 26, 2019
Threads
3
Messages
24
Location
Paulden az
I have noticed an abrupt steering to the left on acceleration and on deceleration the exact opposite. It doesn't matter if I'm on dirt or pavement, launching from a stop or doing 70 MPH. I have a fj40 1978 with a small block chevy running around 450 Hp. It is all stock running gear. Tires are 35 x 1250 15's with a 4 inch lift with S.U.A. I have recently replaced my Ranch o springs with Alcan springs which are a little softer ride. I installed new shocks Fox pro series which are tune-able for compression and rebound. I am thinking I might be having axle wrap but I don't know if this would cause these problems. In the sand the vehicle will lunge out of the sand and then dig back in over and over to the point where I have to back off the throttle for fear of snapping an axle. Thinking of installing a anti axle wrap bar on the vehicle. Any ideas or helpful thoughts on this?
 
Bump steer. Your suspension unloads on acceleration and loads on deceleration changing the angle of drag link as compared to the tie rod. They are supposed to be close to parallel. Lower stiffer springs, a drop pitman arm and/or high steer arms will help. It is a limitation of the straight axle steering design, amplified by your lift and high HP engine.
 
how about pics of the front end and axle assembly.
axle wrap is the rear axle which shouldn't effect steering
with your horsepower a wrap bar is probably a good idea

my WAG is when you accelerate the rear end goes down, front end unloads thus making the steering do it's thing, when braking the front end loads up, compresses thus causing it again. seems it's a horsepower and spring rate issue. could also be a tire preasure issue adding to it.
 
Last edited:
I could be wrong, but my guess is as soon as you put on a rear traction bar to eliminate rear-end wrap-up/hop/bounce, then your 450 H.P. would just as soon crack your transfer-case in half as look at it. All the high H.P./Torque you are presently throwing into suspension movements is pulling it away from your transfer-cases idler shaft, after traction bar, not so much. Oh, and I've got a sales pitch too, I happen to have a brand new in the box Warden billet aluminum transfer-case housing in my ebay store, bullet proof I'm told.
 
I could be wrong, but my guess is as soon as you put on a rear traction bar to eliminate rear-end wrap-up/hop/bounce, then your 450 H.P. would just as soon crack your transfer-case in half as look at it. All the high H.P./Torque you are presently throwing into suspension movements is pulling it away from your transfer-cases idler shaft, after traction bar, not so much. Oh, and I've got a sales pitch too, I happen to have a brand new in the box Warden billet aluminum transfer-case housing in my ebay store, bullet proof I'm told.


finding the next weak link in the chain. custom "split" case.
 
tie rods.webp

Rear locker. ?
No just the front
 
I could be wrong, but my guess is as soon as you put on a rear traction bar to eliminate rear-end wrap-up/hop/bounce, then your 450 H.P. would just as soon crack your transfer-case in half as look at it. All the high H.P./Torque you are presently throwing into suspension movements is pulling it away from your transfer-cases idler shaft, after traction bar, not so much. Oh, and I've got a sales pitch too, I happen to have a brand new in the box Warden billet aluminum transfer-case housing in my ebay store, bullet proof I'm told.
The same Downey that has or had the Toyota dealership? If and when I find out I'm thinking I might go with a chevy trans and transfer case. Hope I dont need to.
 
Bump steer. Your suspension unloads on acceleration and loads on deceleration changing the angle of drag link as compared to the tie rod. They are supposed to be close to parallel. Lower stiffer springs, a drop pitman arm and/or high steer arms will help. It is a limitation of the straight axle steering design, amplified by your lift and high HP engine.
That a block head H.D? Thank you so much for your input.
 
Max drop is about half that height, but yes.

.. and drivers side shackle appears loose, and wonky. There might be other loose suspension components on those springs..

Bob in CO
 
The same Downey that has or had the Toyota dealership? If and when I find out I'm thinking I might go with a chevy trans and transfer case. Hope I dont need to.
Yep, the same guy. I started Downey Off Road Mfg. at the Downey Toyota dealership, that's where the Downey word in the name came from.
 
Back
Top Bottom