FJ43 pre-purchase advice/help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 6, 2004
Threads
29
Messages
350
Location
Alabama
We have been in the market on and off for a FJ40 or 43 for a while, this one ran across my radar.

Its a distance from my house so looking for any input/general thoughts before I go see it (I know pictures are hard to tell) and what to look for on these SA trucks

It is a Columbian "restoration" - whats right, whats wrong/pieced together, it’s listed as a 1979
(just me or does the radiator look patched?)

Greatly appreciate any advice
Front 2.jpg
Front Dash.jpg

Front Driver Side.jpg
Engine 2.JPG

Back.jpg
 
Last edited:
We have been in the market on and off for a FJ40 or 43 for a while, this one ran across my radar.

Its a distance from my house so looking for any input/general thoughts before I go see it (I know pictures are hard to tell) and what to look for on this SA trucks

It is a Columbian "restoration" - whats right, whats wrong/pieced together
(just me or does the radiator look patched?)

Greatly appreciate any advice
View attachment 2581243View attachment 2581244
View attachment 2581245View attachment 2581246
View attachment 2581248
I see you're in AL, is this the one Cahaba Cruisers has for sale?
 
It’s not, I’ve seen that one online this one is not going to be anywhere near that nice, I have some lipstick on a pig concerns just wondering if justified

this one is in Florida
 
You are justified 100%. Flipper. I was typing painted pig as you replied. Florida has many ports to bring these trucks in....so.
Not sure what the $ was but, you can trust more people here selling an honest 40. Not an expert just my my .02.
 
Last edited:
Do you have more pics? Of course, it doesn't have a heater or AC, so if you want to have those creature comforts expect to add another $1,000 - $2,000 depending on whether or not you want to go OEM or aftermarket and do it yourself vs. paying to have someone else do it.

And yes it's a LatAm spec that can hide lots of stuff, but it's a 43 and that's worth the risk sometimes. I have a LatAm spec BJ40 and I rolled the dice for the diesel. Lots of work to do on my part but I'm glad I have it. So LatAm spec vehicles can be good, if you go into eyes wide open.
 
I drive a LatAm spec 43 and its a peach. I think with any vintage vehicle you have go see it and crawl around, in and under it, maybe several different times. Of course you gonna look for rust and body work. Don’t expect it to be the same as a NA 40 under the hood. Mine is a 1981 and the distributor is like a NA 1975. The carburetor could be worn out too? No NA pollution parts just pure 2F power, I liked that part! No PS or heater either but you can deal with that later. It looks like original upholstery up front. Are the jump seat there? It wouldn’t surprise me if it was resprayed red on top and black on the bottom either. Of course you’ll also measure it’s drivability. How many original parts does it have on it from the nuts and bolts and wire run and loom plastic hold downs? The few photos provided make it look clean and intact. Find out who imported it and what shop cleaned it up. Did it come from Relik Garage for instance?
You have your work cutout for you but I wouldn’t be afraid of it, you know your gonna have to work on anyways!

And if your uncertain you can always contact @aljollano or @TWatson who are MUD members and sell legitimate FJ43’s.





devo
 
The flange at the front of the doors ends before the bottom of the door. 1/79 was the start of 79 models and flange ran all the way down. Running boards were notched for the flange. Rear sill seams looks like 1/79+. Front bib looks pushed in at the bottom. Fancy new paint would never buy without a personal inspection. If you don't know the 40 series would have someone who does with me to help point out what's good and what's bad then decide if you think it worth the money.
 
If you tell us the asking price it would be easier to tell if it's worth spending the time to go look at it.

A.J
 
Good advice above particularly the three before this. I don’t see a Vin tag on the firewall (should be on upper passenger side). I’d take a good look at the suspension and frame. Many of these rigs were worked hard.
 
Last edited:
I did get some more pictures and info

I can ask for the vin if it helps

asking 25.5K with 22km (which sounds too good to be true)

Engine.webp
Under Body.webp
Exhaust.webp
Front Seat (Passenger Side).webp
Right Side.webp
 
@devo @Living in the Past @FJ43 1980 @aljollano

Thank yall, thats why I lurked these boards for yh
Im sorry but does not look like a 22km truck. Maybe the digits in the dash say so but not on the undercarriage. Also, it could be an early 79 since the tank is inside and not under. Just my 0.2 cents
 
Last edited:
Depending on how bad the body work (Bondo and rust) price isn't that bad. But body work is a huge question. Ask for pictures under the mats. Gas tank under the passenger is pre 1/79. Most everything says it's a 78 not a 79. Huge difference how the tub was made starting 1/79. Guessing the exhaust routing is stock for 78. Run so low under the skid plate (if it has one) doesn't brake much to get dented crushed off road.
 
Def not a 22km truck. As to the VIN tag, the concern is that it is missing. Even if the truck was stolen at some point it’s typically replaced. Looks like a mishmash of body parts with post ‘79-‘bib and bezel on a pre ‘79 tub (gas tank in cabin). Fenders look like aftermarket. Radiator & fan shroud look buggered. I’d check for front end damage. That said it is a 43 with no pollution crap and pure 2F power! Should get eyes on it and underneath it.
 
The 22km is impossible to verify on a LatAm spec vehicle and very unlikely, so disregard that entirely.
Close ups of the usual rust spots would be good to see, but the frame and underneath looks to be in pretty good shape. So hard to tell w/o getting your eyes on it.

That's not a ridiculously obscene price, which is nice. If I were serious about a 43, I would go look at this in person but be ready to walk away. Look for overspray, paint bubbles, make sure everything worked. And then find a number you are comfortable with.

Sometimes the VIN plate isn't on the LatAm ones, depending on their original destination country. (some were "finished" in the destination and didn't get all the id plates)
 
Im sorry but does not look like a 22km truck. Maybe the digits in the dash say so but not on the undercarriage. Also, it could be an early 79 since the tank is inside and not under. Just my 0.2 cents
yea pretty much what i was thinking assuming gauge cluster could easily not be original
 
I'm not certain, but some of the discrepanciees in body panels and such could be correct for a LatAm model. Most of the observations appear to be based on US Spec 40s.
 
Back
Top Bottom