FJ40 Tub Alignment Process

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 21, 2019
Threads
3
Messages
17
Location
Montauk, New York
Hey guys, I just created my account here. I have been reading these forums for the last year and figured I should begin to post and give back. Anyway, I have been restoring (replacing) a 1978 FJ40. I bought a used tub from Cali and had it shipped to New York and put it on my truck. The alignment definitely seems off as the fenders and hood and apron seem to line up incorrectly. Does anyone have a good process for putting the tub on and aligning it properly? Thanks
 
I don't have an answer for you, but I'll be following this thread because I'll be doing the same thing. Im trying to get my tub from florid and to NY. How much did you pay for shipping and how was it shipped?
 
Watching this too. I bought a replacement tub for my '71 FJ40 and will probably pick it up in California. I'll also have to get mine installed and aligned.
 
First make sure your frame is square. then square the body/ level it then loosely attach the tub the fenders bib and "tweak" as required. It could involve anything from a few tie downs and/or a BFH to a jig and chain pull to straighten it out.
 
Did the tub seem square before you started bolting on the front clip?

Is the rear crossmember of the frame even and flush with the rear of the tub?

Same distance from the two running board stays to the rocker panels?

That’s where I’d start.
 
@65swb45 What is the front clip? I put the tub on this summer and don't really remember anything having to do with a clip. Just a bunch of body mounts and bolts.
 
I actually got the truck from Montauk but mine is in East Hampton as well! Small world! You have a 78? I have really stripped this thing down and built it back up but will be great to compare it to a 78 sometime!
 
I actually got the truck from Montauk but mine is in East Hampton as well! Small world! You have a 78? I have really stripped this thing down and built it back up but will be great to compare it to a 78 sometime!
Yeah I have a '78 as well. If you need some measurements or something shoot me a PM. Happy to help out local mudders.
 
When I put my '78 back together I didn't have to worry about the tub (cab in my case) because I didn't remove it.

But for you, make sure the tub is on squarely. You won't be able to do this if the frame is out of square.

The front clip goes on next. That is the fenders, aprons, bib and hood.
Put those on loosely. You will see a lot of the bolt holes for those parts are elongated to allow for adjustment.
Then line things up and tighten bolts as you go. Start with hood and use that as the template for all the other parts.
Look at pic on this site for approximate gap sizes between parts.

I lived in Port Jeff for a year a long time ago. Still keep in touch with several friends from LI.
 
Guys this is awesome material so I appreciate the help and the rapid responses. It seems that many other forum members can benefit from this. I guess I will take off my tub and check my frame. Why would the frame not be square though? I am curious how you check that it is square.
 
See Part V of Chassis & Body Repair Manual.
 
You never answered my questions. That would tell you something even before you pull the tub off.
 
@65sw Did the tub seem square before you started bolting on the front clip?

Is the rear crossmember of the frame even and flush with the rear of the tub?

Same distance from the two running board stays to the rocker panels?

That’s where I’d start.
Did the tub seem square before you started bolting on the front clip?

Is the rear crossmember of the frame even and flush with the rear of the tub?

Same distance from the two running board stays to the rocker panels?

That’s where I’d start.

I'm not with the truck now but I will be sure to check that out. The rear crossmember was flush and even with the tub. I had to fashion a new rear sill because the previous one had rusted through.

I will measure the running boards to the rocker panels because I think this section would make a very big difference in fender alignment. I definitely will check that out. Tub seemed square, I am not really sure what you mean by that though!
 
If the distance to the rockers is the same, and the rear sill and crossmember are parallel, that section of the frame is probably square/ok.
 
At the end of the day, keep in mind that these trucks were essentially built as tractors in a time that standards weren’t super high. Gaps are also wide in some places (ie where cowl meets the front clip) to allow the panels to move as the frame flexes.

To get things more precise may involve elongating holes and shimming things. At the end of the day it’ll look good... but don’t expect 1/8” gaps that are perfectly even... think tractor.
 
Back
Top Bottom