Experienced Rubithoners

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 12, 2006
Threads
164
Messages
1,226
Location
Ladner, BC, Canada
Website
www.lentelconstruction.com
I am wanting some advice from you experienced Rubithoners. I am trying to decide on the size of lift to put in my 1994 80 series. In the next few years I would like to experience Rubithon with my 80 and I want to make sure I have the right set up. I don't want to put a lift in now and realize in a few years that I have a set up that won't work on Rubithon.

I am wondering if a OME 75mm(2.5"-3" in American) heavy lift with 315's (35's) is enough. If I don't have to spend the extra $ on a higher lift I don't want to. I would appreciate input.

Cheers
 
No lockers, but will have a winch. I could always consider an air locker or some how find an affordable way to swap in factory lockers by then. Which ever is less $.
 
~5 inches of lift, 35's, locks at both ends and armoured all around will get you through "fairly" clean (with good spotters). That is how I set my wife's truck up and it came through with only minor damage on both quarter panels.
 
No lockers, but will have a winch. I could always consider an air locker or some how find an affordable way to swap in factory lockers by then. Which ever is less $.

Without lockers front and rear, it would be quite a challenge at points. Much more important than a winch.
 
I have a heavily weighted down J lift that gives me about 3" of lift with all the accessories I am carrying. Thats 3" above a stock truck without any accessories. I also run L OME Shocks
 
I have a heavily weighted down J lift that gives me about 3" of lift with all the accessories I am carrying. Thats 3" above a stock truck without any accessories. I also run L OME Shocks

I've run it several time with a 4" lift and 35's. Also did it once with Romer and Cdan and we all did fine so i guess now you have 3/4/5 inches supporters. There are places that are scary off camber so one might argue that the least lift that gets the job done may be good, like Romer's 3". Keep CG down.

There are definitely places a rear locker at least will be quite helpful.
 
If you are in a group and can be placed in between locked/winched trucks it's not that big a deal.
 
I am wanting some advice from you experienced Rubithoners. I am trying to decide on the size of lift to put in my 1994 80 series. In the next few years I would like to experience Rubithon with my 80 and I want to make sure I have the right set up. I don't want to put a lift in now and realize in a few years that I have a set up that won't work on Rubithon.

I am wondering if a OME 75mm(2.5"-3" in American) heavy lift with 315's (35's) is enough. If I don't have to spend the extra $ on a higher lift I don't want to. I would appreciate input.

Cheers
35s on 2.5" should work but I think anything less than 4" means a bit more rubbing on the armor in places.
IMO the troublesome areas for my 80 were the result of it's width more than ground clearance.

no locker likely means some winch time especially if the trail is at all wet

I've run it several time with a 4" lift and 35's. Also did it once with Romer and Cdan and we all did fine so i guess now you have 3/4/5 inches supporters. There are places that are scary off camber so one might argue that the least lift that gets the job done may be good, like Romer's 3". Keep CG down.

There are definitely places a rear locker at least will be quite helpful.

Don't forget them fancy rear arms Dave ;)
 
Back
Top Bottom