Electric Seat Problems

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 7, 2016
Threads
176
Messages
939
Location
Decatur GA
Hoping the gear and cap screw were my problem, I ordered the new cap/gear set from Gamiviti (Awesome craftmanship and quick delivery by the way!). After trying the cap first since it had disappeared, I tried the seat out and it did not want to move at all. I can feel the motor trying. And if I sit in the seat and push, I can get the seat to move but you can hear it struggle. I wanted to know if there was a way for the motor to "start to go bad" or would it just die? Or if this is just classic misalignment? Before putting the cap on, I noticed one side wanted to move before the other. There is no stripping or skipping noise though. The gears seem seated.
 
It sounds like you are misaligned.

You can take a pair of pliers and turn the long screw/rod that pushes the seat forward and back. Do this on both sides until the seat is all the way forward while the cap is out. Once all the way forward and both sides are even screw the cap in. This is much easier if you take the seat out (4 bolts). I put a little RTV on the cap threads to keep it from backing out again.

This should have your seat working again. Don't keep trying to use the motor to move it until it is aligned.
 
I appreciate it. Why is it important to have the cap off while doing this?
 
I believe with it in everything is locked together. When you turn the rod for one side of the seat it will bind. With it out you can turn each rod independently until you get the seat aligned/straight, i.e. all the way forward or back. Then put the cap in to lock them together. I haven't done it in a while but if I remember correctly that is why.
 
OK. I will give it a shot. Does not seem like that big of a deal considering I start taking the heater core out next week :(
 
I have done 7-8 seat gear repairs. Don't waste time trying to make it work without replacing the gears. Go ahead and replace the gears, you already have them. THEN parallel the seat rails upon the reinstall and your good to go. Moving them by hand is slow, tedious, and often increases the gear damage. You have already spent your $$ on the kit, so install it. As mentioned, be sure to secure the cap when your done. I usually turn the cap in till it contacts the drive shaft, then back it up about 1/2 a turn so it does not drag.
 
Yes thanks. And I too thought it was going to be a good idea to just go ahead and replace the gears since I am taking it out. I figured by taking both seats out, it would make it easier on me to replace the heater core anyway. 8 extra bolts for that much more comfort.

I hope that the seat problem has been the reason my seat has never gone back far enough for me. I am only 5-10" and I have always felt a little cramped even with the seat all the way back. I was always surprised at this.
 
I recently purchased the Gamiviti gears+caps to fix this same issue in my 80. While the cap was a no brainer on how to install, I couldn't see for the life of me where the gear itself goes.
I've seen mention of some instructions, but can't find them anywhere. Is there a copy in .pdf form floating around?
 
The install point is really obvious for the cap, but the gear is a different story. I believe the seat must be removed and flipped over to replace it. It is only 4 bolts and really easy to take the seat out. Make sure to move the seat all the way to either the front or back to keep from having re-alignment problems. There might be instructions on which way is recommended but I cannot remember. But do not remove the seats until they are moved all the way if you can help it. But I have had to re-align my seats after install and it is not that big of a deal. just do not force them. You will have to rely on feel to know whether or not the seat is under too much torque. You can strip a gear or burn a motor if you over do it. But to be honest, if you burn a motor, then you really, well... Just be patient. Move the seat a little, then adjust, move again and you should notice if the seat is moving better or worse. Use this technique only if the gear is completely stripped/motor burned and you cannot move the seat at all before replacing the gear. The seat alignment is really really precise. You can easily tell when it starts moving the best it can. Also, check out Inkpot's reply earlier. It did help me out a lot.
 
Just finished this job.

This thread, specifically @inkpot s insight on realignment, and the Gamiviti instructions made this a 1.5 hour job.

Make sure you have some lithium grease or something similar for the gears, and other misc moving parts.

I'm assuming this was my problem.....

Old gear.

IMG_6612.webp
 
Back
Top Bottom