Ditched the ABS

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 15, 2004
Threads
336
Messages
2,730
Location
Los Angeles, CA
Website
www.phipsi.net
Time to turn a wrench and this time I finally removed the ABS unit and now have about 4 open ended brake lines. My plan is to either change out the ABS brake master cylinder for a NON ABS Brake Master Cylinder, in which case I wonder if there is a better toyota upgrade I can make that that unit, OR

Keep the ABS one and just tie lines together.

Like to know any recommendations you may have.

I would ideally like to run brand new break lines, but that is not going to happen for now.

Thanks in advance:beer:
 
I'd imagine that it would be tough to find an upgrade that wasn't ABS, since you would probably be looking at tundra or 100 series units, or something of the like. I'd say just run the stock MC and tie the lines together until you need/want to run new lines. From what I have read you will see a small increase in braking simply from taking the ABS unit out. That being said, whatever you do, snap a few photos. My ABS has been unplugged for a long time, and the wiring and sensors are all 86'ed. One of these days I'm going to get around to pulling the unit out of the engine bay.

Ps. Good to see you back on Mud. I thought you may have sold your 80.
 
I'd imagine that it would be tough to find an upgrade that wasn't ABS, since you would probably be looking at tundra or 100 series units, or something of the like. I'd say just run the stock MC and tie the lines together until you need/want to run new lines. From what I have read you will see a small increase in braking simply from taking the ABS unit out. That being said, whatever you do, snap a few photos. My ABS has been unplugged for a long time, and the wiring and sensors are all 86'ed. One of these days I'm going to get around to pulling the unit out of the engine bay.

Ps. Good to see you back on Mud. I thought you may have sold your 80.

I'll snap a few pics for sure, 80 is being worked on BIG TIME hoping to have it wrapped before Rubithon.
 
This is what I did.

IMG_0936 copy.webp

IMG_0937 copy.webp

IMG_0936 copy.webp


IMG_0937 copy.webp
 
Subbd. What's the benefit to getting a non abs master?
 
Did you need to reflare the ABS lines?

I was able to re-use existing lines with some creative tube bending ;p The threads and flare all match and are the same. Braking is much better w/o the ABS module and my fluid stays clean between annual flushing.
 
What's the electrical box in the picture? Also, what is that clear/black tube assembly on the right?

What did you use to bend the brake lines?

I used the smallest brake tubing bender I could find at the local auto parts store. Not much room to make the bends that are needed, but turned out ok.

Plastic box is the controller for my 7th injector. Tube is a manifold pressure sensing line going to the controller.
 
I used the smallest brake tubing bender I could find at the local auto parts store. Not much room to make the bends that are needed, but turned out ok.

Plastic box is the controller for my 7th injector. Tube is a manifold pressure sensing line going to the controller.

What MC did you use? What year? Now since you dont have ABS dose your check engine light or ABS light stay on your dash?
 
I did not change the MC (it's a '94) and yes, the ABS light is 'on'. I have not taken the time to figure out a hack to fake the ecu. Might be as simple as adding resistors or choke at the connector for each solenoid coil. Any ideas?
 
I did not change the MC (it's a '94) and yes, the ABS light is 'on'. I have not taken the time to figure out a hack to fake the ecu. Might be as simple as adding resistors or choke at the connector for each solenoid coil. Any ideas?

Remove the bulb from the dash:doh:

My 94 has ABS removed. A non-ABS MC was put on. Truck is Part-time so ABS wasn't doung anything anyway.
 
I used the smallest brake tubing bender I could find at the local auto parts store. Not much room to make the bends that are needed, but turned out ok.

Plastic box is the controller for my 7th injector. Tube is a manifold pressure sensing line going to the controller.

1FZJ, can you give a step by step break down of what we will need to do the job and how to complete the job from the point of disconnecting the lines to bleeding brakes? Thank you
 
It’s pretty easy. Remove the ABS module (disconnect brake lines and electrical plugs, loosen the bolts holding it to the bracket and lift it out). The module has raised letters ‘F’ and ‘R’ to identify the lines. Discard the short rear line between the MC and the ABS and bend the rear tube (which connected to the ABS output) to fit directly into the MC. You will need a tee to connect the two front lines to the MC which is routed from the tee below the brake booster. I purchased the tee that is used at the rear axle between the soft and hard lines. I think it was $9. You will need a brake line tubing bender, the smaller the better as there is not much room to make the bends. Then do a flush and bleed and enjoy better braking. Make sure you use flange nut wrenches on the brake line nuts.
 
I don't really " think " ( IMHO ) you can't perform an MC upgrade alone .. if we are including calipers then it's another story ..

" upgrading " MC to a bigger bore will decrease pedal travel ( more fluid been moved ) with more firm pedal but you probably will need more foot pressure to archive same brake performance than before ( MC upgrade ) depending on the bore size you choose ..
 
Those of you with ABS delete, is the factory braking scenario still intact - I'm referring to the way the brake lines are connected FL and RR, FR and LR. I assume so, but wasn't sure.
 
Those of you with ABS delete, is the factory braking scenario still intact - I'm referring to the way the brake lines are connected FL and RR, FR and LR. I assume so, but wasn't sure.

Yes. There are two separate circuits, front and rear. The method I described removes the ABS from the system without changing how it is piped or operates other than defeating the ABS.
 
Did you keep the lspv?
 
Back
Top Bottom