DIfferential Questions

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 28, 2004
Threads
70
Messages
285
Location
Orlando, Fl
ok, so i dont know if my trucks diff's have ever had the fluid changed, or even if they have any fluid in them. so i was wondering what kind of fluid i should put in, and how much i have to put in each one.

any help is much appreciated.

Jonathan//Sandrider (she appreciates it more)
 
Search is your Friend!... But since you asked the diff takes 2.5L of 90w (or 80w 90w) GL-4 Gear Oil. There are tons of opionions on what oil is best, I don't have one myself. I was planning on doing a gear oil change before my next outting, but I'm going to hold off since I think I'm seeping oil from the cover gasket and don't have time to do it right. FYI Autozone does sell a 5 gallon bucket of gear oil that is ok to use in diffs, t-case, and tranny.
 
Only after removing the fill plug out of the back of the diff do you want to accually remove the drain plug located on the bottom of the diff itself. If you are worried about the little bit inside of the axle shafts you can throw a jack under each wheel one at a time to lift it and drain the fluid, but I wouldnt worrie about that. Just worrie about getting the fill plug off before the drain plug comes out.
 
ok, thanks for your quick response.

Jonathan//SandRider
 
i went to remove the drain bolts (already loosened the fill plug) but, now im afraid of stripping the bolts, it started to slip and rounded the edges a bit. any sudgestions?
 
k, i gotta go out to get a 6pt 22mm.

i would love to come out, but i have school at night, 7:30 to 12:30
 
I made a tool for removing drain and fill plugs by machining the front beveled edge off the correct size socket. you could however do it with a grinder if you don't have access to a lathe . I find it helps the engagement of the socket and doesn't slip off a easily.
 
get the low pro allen head drain plug, good upgrade
 
Stock drain and fill plugs on Land Cruiser axles are 24mm...


A 6pt socket is the best way to go....


A 15/16" 6pt may also 'fit' and 'work'.


Good luck!


-Steve
 
yeah, 24 mm wont work, it doesnt even come close to fitting on
 
yeah, 24 mm wont work, it doesnt even come close to fitting on



Post up a picture....



Land Cruiser axle?


Did you clean the crap out of the area around the plug?

Is that protective ring damaged and preventing the socket from getting to the plug?


24mm is your drain and fill plug socket...
 
heres my axel, and the 24mm bolt next to the fill plug.

Jonathan//SandRider
axel small.webp
24mm small.webp
 
If the flat edges of the plug are damaged, which they could very well be since it appears that there are some corners that are rounded on that plug, you may need to take a flat file to the flats on the plug to get the socket to fit properly again.


attachment.php
 
Obviously, you don't h8mud. Just a suggestion, spray some water in there and use a stiff bristle brush to clean off the areas around where you are working. You don't want dirt and sand falling into your differentials or your eyes. :doh:

By the way, the little pump really helps with the tranny and transfer case. However, I find it just as easy to dump the oil into the diffs. The pump takes awhile, and the diffs are easy enough to get to with the pointy spout.

Of course, that's all assuming you can get the plugs off. Good luck with that!

:beer:
 
By the way, the little pump really helps with the tranny and transfer case. However, I find it just as easy to dump the oil into the diffs. The pump takes awhile, and the diffs are easy enough to get to with the pointy spout.

Of course, that's all assuming you can get the plugs off. Good luck with that!

:beer:

I buy gear oil buy the 5 gallon buckets and use a metal pump. Much easier than using a plastic pump or trying to sqeeze the gear lube in there.
 
Back
Top Bottom