Cooling issues after replacing everything

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I feel your pain man, been working on my cooling system since purchase in 2015, thought I had it licked but she doesnt like it when ambianet temps reach 103^. I find myself wondering what the hell these trucks were like in the 90s, did they come this way? why were'nt their recalls on FC or rad, etc? I mean my truck had issues when bone stock, and is now minor-ly modified.

If you have an infrared thermometer (Amzon $25) you can shoot it at your rad to see if temp distribution is uniform/normal. If you see anomalies you may have flow issues. Should be hotter at inflow end on bottom and cooler on top (IRCC).

Any sign of coolant in the oil? Yes, engine is working hard, but airflow should be good at highway speeds so FC may not be issue. Head could be warped cracked. These engines are so robust that they can run a long time in this condition, and odds are its been subjected to very high temps at some point b/c they cooling system is so inadequate.

I have a Koso gauge and OEM T-stat on the way for mine FYI, and will be modifying the FC (green hub) to open even earlier. :(>:mad:>:bang:>o_O
 
Just took a CSF out and replaced with genuine radiator to fix an overheating issue. Works like a champ now. We’ve had to do this quite a few times here at Slee. You should still go through the proper diagnostic procedures, but probability says that’s probably your issue :) OE rad coms with a new cap.
 
I'm betting it's your clutch fan. Research the mod and do it. You should hear it roaring. I did mine and it stays nice and cool. Just had a buddy that went through three aftermarket ones before he got one to work. He ended up doing the mod and it fixed his overheating issue. Pick up some 30k fluid and fill it with what you take out. Another method to test is to put a piece of cardboard against the fan while it's idling and see it it's easy to stop when it's up to temp(don't cut your arm off), if it easily stops spinning it's not doing it's job because the oil is too thin. You'll know soon enough what it it is.
 
Last edited:
Just took a CSF out and replaced with genuine radiator to fix an overheating issue. Works like a champ now. We’ve had to do this quite a few times here at Slee. You should still go through the proper diagnostic procedures, but probability says that’s probably your issue :) OE rad coms with a new cap.

So question for everyone. When you go for a OE radiator I assume you are ordering a Denso rad from rockauto or similar and not paying Toyota prices?
 
4000 mile trip through CO and UT a few weeks ago.

100F ambient:
80 mph flat 186
80 mph long steady climb 188
Stopped at light after highway 192
4H crawling 194
4L crawling 188
Stopped while crawling w/AC 198

88F ambient:
55 mph hammering up vail pass 188.6

Other than a modified fan clutch, all cooling system is Toyota parts, fairly new. Prestone coolant. 315’s, mild lift, 4.88’s, low range reduction gear.

I hope I didn’t just jinx myself.
 
So question for everyone. When you go for a OE radiator I assume you are ordering a Denso rad from rockauto or similar and not paying Toyota prices?

TRad is the Toyota supplier, have never seen it offered anywhere but Toyota parts. Have only installed one Denso, but wasn't impressed.
 
Been gittin a lot of 110÷ days, but it was only 105ish yesterday. Went out north of Fountain Hills to evaluate a 2700 acre burn area all afternoon. Ground is really hot, and most rocks are too hot to leave yur hand on in or out of the burn. Rough terrain, and lots to look at. So average speed was <10, and much of it <5 mph. Coolant temps varied between mid 180s and mid 190s depending on how steep the mountain is. AC running 100%. Cabin temp in high 70s.had 1 long, loose cable, steep climb that was very slow. Temps did pass 200 briefly.

So I have a 1 year old TYC radiator, juiced up Eaton fan clutch, full sized fan inspite of running a TRD
S C. OEM pusher fan. Loaded with armor, loaded with cargo. 37s over 4.88s. Normal day in the desert.
 
Coolant Are you using 50/50 or are you buying concentrated mixing it yourself. Is there anything deflecting the airflow like a license plate aftermarket lights. I would do a combustion chamber leak down test to make sure head gasket is not putting air bubbles into the cooling system, air bubbles would make the coolant not circulate properly. the CSF radiator you used looks like it has a copper core I think aluminum core is a much better heat transfer. And like previously mentioned make sure you have no air trapped.
 
Yes, engine is working hard, but airflow should be good at highway speeds so FC may not be issue.
This is a very common misconception.
These trucks are as aerodynamic as a brick. At highway speeds, most air is flowing around the front of the vehicle as it creates a large bow wave. The engine driven fan MUST produce negative air pressure behind the radiator in order for air to flow through.
 
the CSF radiator you used looks like it has a copper core I think aluminum core is a much better heat transfer.

^^^^
Actually Copper has the better Thermal Conductivity than Aluminum, so better at heat transfer. But aluminum is better at dissipating/shedding heat. So the perfect set up (if cost, weight and size were not factors) would be a copper core with aluminum fins.

Not to nit-pick....

I think the message you meant to convey is that most aluminum cored radiators (owing to their construction) will be more efficient than a brass/copper radiator of similar size. This is because Aluminum being the more rigid metal can be formed wider and contain more multi-channels and provide more surface area (whether serpentine or parallel).
 
Last edited:
This is a very common misconception.
These trucks are as aerodynamic as a brick. At highway speeds, most air is flowing around the front of the vehicle as it creates a large bow wave. The engine driven fan MUST produce negative air pressure behind the radiator in order for air to flow through.

^^^^

Could not agree more. The 80 series is quite 'Fan Dependent'. If any doubt this, remove your fan and go for a drive on the highway (hot weather). Compare your coolant temps to those with the fan in place (and clutch working correctly).

'Ram Air' effect and under-hood evacuation are less than stellar in the 80 series.
 
^^^^

Could not agree more. The 80 series is quite 'Fan Dependent'. If any doubt this, remove your fan and go for a drive on the highway (hot weather). Compare your coolant temps to those with the fan in place (and clutch working correctly).

'Ram Air' effect and under-hood evacuation are less than stellar in the 80 series.

A quick under hood temp study will show that the airflow is pretty good, well designed, for an '80s design. Clog it up with a bunch of junk and all bets are off, just adding a second battery significantly impacts it.

My guess, the biggest contributor to the fan dependence is the small radiator. For example, some first gen Tacos have a larger surface area radiator, cooling a significantly smaller motor. Shoving a bunch of air through a smaller hole, takes more fan.
 
Oh no, thats exactly what I didn't want to hear haha. Do most people continue running it or swap it out for something else? Right now I'm leaning towards doing all the other improvements and seeing if that will lower the temp enough.

I swapped new CSF after one year or so to TYC and now life is good

 
Last edited:
4000 mile trip through CO and UT a few weeks ago.

100F ambient:
80 mph flat 186
80 mph long steady climb 188
Stopped at light after highway 192
4H crawling 194
4L crawling 188
Stopped while crawling w/AC 198

88F ambient:
55 mph hammering up vail pass 188.6

Other than a modified fan clutch, all cooling system is Toyota parts, fairly new. Prestone coolant. 315’s, mild lift, 4.88’s, low range reduction gear.

I'm impressed with holding 80mph up a long climb more than I'm impressed with that water temp.


But the plan is this coming weekend knock out the fan clutch mod and the other todo list stuff. See how that works on a trip and then maybe look into a TYC radiator. Thanks for the help everyone.
 
@flintknapper and @jonheld gona need more convincing on this one...A literature search reveals this is very difficult to measure and still an ongoing pursuit of car manufacturers to figure out optimal cooling-air drag ratios; In flowing air, exiting air, angle and size of grille, mph, radiator size, water pump efficiecny, fluid, etc. etc.:

"The interaction between underhood airflow and external aerodynamics is not yet fully understood"
"The influence and impact of cooling flow rates are not studied and configurations favorable to engine cooling are undetermined."

The likelihood of overheating caused by the FC not pulling air at highway speeds is a stretch for me. What sort of readings do you get when you run your electric fan on the highway? cooling? how much?
 
@flintknapper and @jonheld gona need more convincing on this one...A literature search reveals this is very difficult to measure and still an ongoing pursuit of car manufacturers to figure out optimal cooling-air drag ratios; In flowing air, exiting air, angle and size of grille, mph, radiator size, water pump efficiecny, fluid, etc. etc.:

"The interaction between underhood airflow and external aerodynamics is not yet fully understood"
"The influence and impact of cooling flow rates are not studied and configurations favorable to engine cooling are undetermined."

The likelihood of overheating caused by the FC not pulling air at highway speeds is a stretch for me. What sort of readings do you get when you run your electric fan on the highway? cooling? how much?

Interesting read (if any want to take the time, I did). Unfortunately many of the studies cited are 25 to 40+ years old. Other's more recent. In the end....little was contributed that we don't already know.....and NONE of the 'testing' done on our vehicle, just 'principles' to apply.

It is understood that studies continue and that all aspects of airflow (for the purposes of cooling) are not perfectly defined.

Suffice to say....that back in 1990-1991 when the 80 series (as we know it) was unveiled, there was not as much technology to draw from. I'm sure Toyota did the best they could at the time.

The only 'electric' fan I have on my 80 series is an AUX fan I added to aid in condenser cooling at low speeds, it obviously is not meant for cooling the engine....so I can't answer your question about that.

As for the Engine Mounted Fan/Clutch.....I will not try to change your mind...nor 'convince' you it plays an important role (at all normal speeds) in controlling engine temps. Clearly the fan is most needed...at low engine speed when Ram Air is not present, no one will argue that (or shouldn't). But it is also contributing (to a point) at higher speeds. And for those with accessories (bumpers, winches, lights, 2nd batteries, OBA) which change/impede the airflow....you need all the help you can get.

As I stated before...if you doubt, pull your fan...go for a long highway drive (monitor with a scangauge/other). I am more than willing to be rebutted.
 
Back
Top Bottom