Clutch fork location

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 9, 2016
Threads
19
Messages
55
Location
Rahway nj
The previous owner put a f155 engine with a 4 spd trans in my 71 fj40 the minor problem im having is that the slve cylinder which is now located on passenger side will not fully disengage the clutch because the fork is being blocked by part of tub.brace. I can cut it back a slight amount or is there a way to move fork to other side anyone have this situation - looks like if i trim it it wouldnt be a big deal. Anyone??? I appreciate it i enclosed pics and outlined what i would have to trim - or can i move it to drivers sidr

7BE92995-8E17-4FB8-B326-E7D47003ABF1.webp


827CD4A5-E779-4750-9A74-853C828EAE11.webp


A10A9251-BAFB-48DF-83AB-BAB7C46EAE91.webp
 
Why u think its like that is it a different tub design in 71 than the74 which motor and trans came out of
 
Came out of a 1974 fj40. ?? And later 74 and on they relocated slave to passenger side. F155 was transitional engine between 1f and 2f. The oiling system of the 155 became the oiling system of the 2f thus it was a better system than the f engine
 
Thanks for the info. Do you have any idea of how much work would be involve in moving the cyl to the other side????

JUST TRIM THE BRACE!!! Save yourself a lot of grief.
 
I believe early FJ40’s (maybe pre 1974?) had the clutch fork on the drivers side, and the later ones moved to the passenger side. I’m fairly sure that’s true I’m just not sure when the transition happened - maybe when they went from 3-speed to 4-speed?

I run a passenger side fork on my 75 - but when I got it everything had been converted to drivers side. I didn’t run into the tub brace conflict but my truck is V8 converted so nothing is quite where it should be.

Not a lot of engineering involved in moving it - just build a new hydraulic line. The PITA part will be dropping the transmission to move the fork over.
 
I believe the slave position cutoff date is 8/1974 where it went from driver to passenger side (US). I am currently going thru the opposite transition. I am going from driver's side to passenger side on my pre-8/1974. It doesn't appear as though I'll have this same issue on my truck, but my body is a 1976. This thread may or may not help if you haven't read it yet... Mixing clutch slave parts from different years
 
Last edited:
Funny that the early (at least ‘63) bellhousings have the clutch fork port hole and hole for the clutch fork pivot bolt on both sides. Trying to imagine what was common between LHD and RHD in keeping the slave on the “driver’s” side for each. Not even the hard line from the MC to the cowl bracket where it attaches to the soft line running to the slave cylinder would be common unless the cowl bracket was mounted differently for each (different position relative to cowl support member). Oh well, no sense wasting too many brain cells on that one.

Can’t the clutch fork be removed without pulling the tranny?
 
Last edited:
Can’t the clutch fork be removed without pulling the tranny?

Not that I'm aware of - it clips to the throw out bearing so you'd need to unclip it to pull it. That part might be possible but I can't imagine it would be easy to get those clips reinstalled through the ports in the bellhousing.

EDIT: One second thought, maybe you can with a stock bellhousing, via the inspection port on the bottom if yours has one. I've got a "full circle" housing without a port so that isn't an option for me.
 
My Oct 71 (72) had and my 75 40 has the slave on the Dr side. I Purchased a 76 for the driveline and the slave was on the pass side. So when I updated the driveline on the 72 I just ran a new hardline to the pass side. I think the bellhousing is designed to go either way.
 
EDIT: One second thought, maybe you can with a stock bellhousing, via the inspection port on the bottom if yours has one. I've got a "full circle" housing without a port so that isn't an option for me.
Well, I wasn’t paying attention, this is a 4-spd bellhousing so it doesn’t have the inspection port like you mention. I think it’s possible to unclip the throwout bearing hub on a 3-spd with inspection cover removed, if the fork pivot is unbolted first. Mute point with a 4-spd anyhow.
 
I notice on the other side of bell housing there is a port with a rubber cover is that to switch the fork to other side
 
Well, I wasn’t paying attention, this is a 4-spd bellhousing so it doesn’t have the inspection port like you mention. I think it’s possible to unclip the throwout bearing hub on a 3-spd with inspection cover removed, if the fork pivot is unbolted first. Mute point with a 4-spd anyhow.

You sure? I could have sworn all years had an inspection port on the stock bellhousing.
 
You sure?

No I’m not sure at all, lol. Complete brain f@rt on my part. Before my 2nd cup of coffee for sure. Your “full circle” bellhousing must be for an SBC? Mine is on my ‘65 40 SBC.
 
Not that I'm aware of - it clips to the throw out bearing so you'd need to unclip it to pull it. That part might be possible but I can't imagine it would be easy to get those clips reinstalled through the ports in the bellhousing.

EDIT: One second thought, maybe you can with a stock bellhousing, via the inspection port on the bottom if yours has one. I've got a "full circle" housing without a port so that isn't an option for me.

It sucks. I’ve had to get a fork back on those clips after it slipped off during a stubborn transmission install and it was not fun.
 
Back
Top Bottom