Carb help with 1982 FJ40

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 13, 2017
Threads
68
Messages
442
Location
Wickenburg, Arizona
Our 1982 FJ40 starts, idles and runs fine. Doesn't smoke or burn oil. 108K miles on original motor. It was desmoged by the original owner in 1997. When I talked with him last summer shortly before he died, he told me "I had the jets drilled out..." for better performance. That's an old school term I hadn't heard in a long time. He lived in Florida. I'm in Colorado at 8,200 feet. The rig will see 10-12,000' on some passes this summer. I seem to be a little lacking in power especially running the A/C. I'm wondering if I should think about overhauling the carb and putting in jets more suited for the altitude.

I'm assuming this is the original carb since almost everything else is original.

IMG_3550.webp


IMG_3551.webp
 
A 2F at that altitude is going to be challenged no matter what. Jetting it down for high altitude is appropriate, especially with the original jets being opened up. It will help with fuel economy and driveability (emissions testing too if that is in play. Other than the fact the rest of the stuff has been ripped out) but you won't get any more power out of it.
 
The "U" - shaped piece of vac hose on the air horn of the carb means the HAC (High Altitude Compensation) apparatus was prolly removed as part of the desmog. A carb at altitude will run rich because of less-dense atmosphere. Yours is prolly running extra-rich if jets were reamed.

The HAC allows about 5% ish more air to bleed in when above 4K ft to lean the mix. It may very well be time to have the carb rebuilt and tuned for you purposes. You might even try to locate a HAC setup to improve drivability - I believe it's the same as the FJ60, but not 100% on that.

www.marksoffroad.net
www.TLCPerformance.com
 
Yes, its drowning in fuel at that altitude. That hurts power & driveability.

Try opening up the 3 HAC ports as a first step. Two of the HAC ports are connected to each other on the top of the carb, which is a real flustercluck with different carb circuits stealing air & fuel from each other.

Check that the carb is hitting WOT when the gas pedal hits the floor.

The AP linkage is missing a nylon bushing under the rocker arm.

Since there is no HAC, the timing will need to be advanced about 8° ahead of sea-level spec.

The dissy cap ventilation system is inop, so the dissy should be inspected to see if the vacuum advance & mechanical advance are still working. Some sort of vent system should be implemented.

HTH.
 
Thanks for the info. Since I'm desmoged, can I retrofit the HAC on it? What about availability and instructions?
 
For 'instructions', you need the Toyota emission manual for your year of truck (see sor.com for reprints).

Our 1982 FJ40 starts, idles and runs fine. Doesn't smoke or burn oil.

In some ways, if it ain't broke, don't fix it. I'm sure that it will smoke a bit black on high mountain passes in Colorado, but if not, the (for whatever reason) it may not be running very rich. Is your fuel mileage acceptable?
 
For 'instructions', you need the Toyota emission manual for your year of truck (see sor.com for reprints).

Our 1982 FJ40 starts, idles and runs fine. Doesn't smoke or burn oil.

In some ways, if it ain't broke, don't fix it. I'm sure that it will smoke a bit black on high mountain passes in Colorado, but if not, the (for whatever reason) it may not be running very rich. Is your fuel mileage acceptable?

Fuel mileage kind of sucks. Kind of hard to get an accurate figure because of speedometer/odometer error due to oversize tires. I'm kind of thinking of going with "if it ain't broke, don't fix it."
 
It is without doubt being over-fueled now. That really ought to be addressed, even if you do nothing else.
 
Who is offering proper jets, what jet sizes are appropriate? Getting stock carbs tuned into the mountains is pinnacle.

Does this carb / dizzy necessitate HAC, or can it be conveniently de-HACed?
 
There are some threads, maybe in the 60-Series section, about a proper system to vent the distributor. And I believe there is a lot of information about how the HAC system functions. But as FJ40Jim has said, simply advancing the timing can take care of that. Here's another innovative method:

Manual HAC

If you want to add back in some of the components and systems, the beneficial ones, to get to the most common de-smog (threads and diagrams here on MUD) configuration, a short trip down the road to Classic Cruisers in Poncha Springs could probably net you the parts you need.
 
Thanks for the continued comments. We're camping for a week with very sporadic Internet. I'll be getting back with some of you in about a week.
 
Back
Top Bottom