Brake issues

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 17, 2019
Threads
2
Messages
9
Location
Austin Texas
I'm working on a friend's 1970 FJ40. I've replaced the front and rear wheel cylinders. So all 8 wheel cylinders have been replaced. I blew out the lines while I had it apart and made certain all the air was out of the lines. Now when you go for a drive the front brakes get stuck on and lock the front wheels up. I'm at a loss here. I've spent hours trying to figure them out and I'm just stuck. Has anyone had an issues like this? am I overlooking something because I'm just so dang tired? Any help is appreciated
 
Look up smoking brakes ... common issue

X2 @thebigredrocker

The brake peddle adjustment ... eitherthe rod between the booster and master or the peddle rod is out of adjustment

Another issue is if your missing the brake peddle return spring ... resting on the rod it will then mimic the adjustment being off
 
the OEM drum brakes master cylinder has residual valves that keep proper line pressure
 
Look up smoking brakes ... common issue

X2 @thebigredrocker

The brake peddle adjustment ... eitherthe rod between the booster and master or the peddle rod is out of adjustment

Another issue is if your missing the brake peddle return spring ... resting on the rod it will then mimic the adjustment being off
I'll try and see if it's out of adjustment. I have no idea what's going on with them anymore.
 
the OEM drum brakes master cylinder has residual valves that keep proper line pressure
Could a master cylinder rebuild possible solve the issue if it's got a bad valve? Is there any way of testing to see what's going on?
 
I'll bet you have one of the rubber pieces in one of the slave cylinders in backwards
I can take them all apart again. But what are the odds that I only messed up on the two front wheels? I'm pretty sure I got them together correctly but it never hurts to double check I suppose. Iv put several hours in trying to get them right.
 
Could a master cylinder rebuild possible solve the issue if it's got a bad valve? Is there any way of testing to see what's going on?

the valves are easy to access: they are behind the big hex nuts on the outside of the master cylinder - black round plastic thingies - of course, afterwards you'll have to bleed the entire system again :bang:

but I would first check on the return spring - much easier
 
When I did it , it was on an old willy's cj5. I was driving in a snow storm and the roads where packed. The front driver tire was just skidding along. The drum was hot when driving on the dry road. I had to pull over and crack the nut on the brake line to lose the pressure. It was good for about 4 to 5 brake peddle pushes, but the pressure was building again. I found one of the rubber cups in backwards.... :smokin: oops what can I say. It was just one of those days :beer:
 
I'm not going to assume that you have a 7/70 or newer with the dual circuit master and booster. But even with the pre-7/70 setup, a mis-adjusted pushrod will cause this. Made that mistake on my first 40, 32 years ago.

It happens.
 
Did you just do the slaves and not touch anything else?
Rebuild or new?
If you didn't have the master off and the brakes were not locking before you did the rebuild then the peddle adjust should be alright.
Might double check though.

If you got the cups in backwards there should be a massive amount of brake fluid leaking out and I doubt you would have manged to bleed the brakes properly.
There is a slight difference but the shoes may be on backwards that can cause them to bind.
In the SOR brake section there is a nice picture of how each wheel should look.

Are both front wheels locking?
This usually only happens on one wheel at a time but moving the rubber line and any undue stress, especially on old hoses, could cause the inner lining to stress and cause a one way valve effect that will not let line pressure release.

Last thought, are the return springs attached right?
 
Did you just do the slaves and not touch anything else?
Rebuild or new?
If you didn't have the master off and the brakes were not locking before you did the rebuild then the peddle adjust should be alright.
Might double check though.

If you got the cups in backwards there should be a massive amount of brake fluid leaking out and I doubt you would have manged to bleed the brakes properly.
There is a slight difference but the shoes may be on backwards that can cause them to bind.
In the SOR brake section there is a nice picture of how each wheel should look.

Are both front wheels locking?
This usually only happens on one wheel at a time but moving the rubber line and any undue stress, especially on old hoses, could cause the inner lining to stress and cause a one way valve effect that will not let line pressure release.

Last thought, are the return springs attached right?
I have a 7/70 model. I checked the cups they are put in the correct way. The slaves were rebuilt. And the springs were in the right way. I finally took the master off and took it apart. Found some sludge in it so I have it pulled apart and I'm waiting on a rebuild kit for it as well crossing my fingers.
 
I'm not going to assume that you have a 7/70 or newer with the dual circuit master and booster. But even with the pre-7/70 setup, a mis-adjusted pushrod will cause this. Made that mistake on my first 40, 32 years ago.

It happens.
It is a 7/70. Checked the adjustment. I'm pointing blame on the master cylinder right now hoping that a rebuild will fix the problem.
 
Back
Top Bottom