Blown Engine 66 FJ40

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 25, 2015
Threads
4
Messages
26
I blew the bottom radiator hose and I lost water so fast i did not even see the temp rising. The engine started clattering and missing badly.
Towed my rig to my shop
Not knowing all that is wrong, I first replaced all radiator hoses, including heater hoses.
Started engine and it still clattered, noticed oil pressure was good.
Sound more like a valve may be slapping the top of the piston?
The real question is "what to do".
First thing is to remove the hood, it appears the lower end is OK
Worst case is I will need to do a complete rebuild or another engine. I do have a spare head.
I am sure I will be needing parts, so any suggestions of where to get engine parts or short blocks.
I want to keep the rig stock if possible.
Right now I need suggestions and maybe a hug.
 
  • Sad
Reactions: flx
Got my rig in the shop and pulled the valve cover.
Found two push rod that had become unseated and of course they are both bend.

Do not know if the cam or the pistons are damaged.
Next step is to pull the head and check the pistons and pull the side covers and check the cam.

Not sure why or if loosing all my coolant would cause this?
 
Get a cheap bore scope and look into each cylinder to see what's going on.
 
Where are you located?
 
I would pull the head at a minimum. Heat marks on the cylinder walls are not the easiest thing to see with a boroscope, but pretty apparent in daylight.
 
Probably a stuck valve from overheating, throw some push rods in it, adjust the valves! These are non interference engines, should be fine As these are bulletproof tractor engines!
I spent 2 hour searching for push rods and could not find a source, any suggestions?
 
Probably a stuck valve from overheating, throw some push rods in it, adjust the valves! These are non interference engines, should be fine As these are bulletproof tractor engines!
As I have more time than I have money I am going to pull the head. The main reason is that one of the push rods did not come completely off and was caught under the adjustment nut thereby opening the valve mush farther than they should be and that could be the slapping noise I heard. I also have a spare head in case the valve is bent or destroyed.
 
I have some pushrods from a 1970 F engine (well, lots of different ones actually….). If you need a couple few, they are yours for the cost of shipping.

But I’d try to get that head off and inspect.
 
F135 Pushrods are VERY different. In a pinch you could weld two together to make a trail spare. I know; I did it 12 years ago:

 
F135 Pushrods are VERY different. In a pinch you could weld two together to make a trail spare. I know; I did it 12 years ago:

It’s good to have knowledgeable people like you on here, willing to share.
 
I have some pushrods from a 1970 F engine (well, lots of different ones actually….). If you need a couple few, they are yours for the cost of shipping.

But I’d try to get that head off and inspect.
Appreciate it, I will need at least two that I know are bent. But first I am going to pull the head, already have it half of but found a problem with the exhaust manifold where it connects to the exhaust pipe, broken tab and frozen bolt, I am sure that will tke me more than a few hour to get undone. I wasn't going to remove this until I saw the both was loose and frozen and the back tab was broken, I just love working on these old rigs. LOL
 
@Bzerker999
just south of you, I don't have any 135 pushrods but lots of other parts if needed.
also check in here:

Appreciate the offer. I am still in the investigation phase, hope to have the head off today, but the exhaust manifold is giving me fit but what is unusual about that
I am confused, I see "135" mentioned is this what is in a stock 66 fj40?
 
F135 would be stock, it has siamese ports on it
a pic or two would determine if it is a stock engine for the year
 
Also the date code on the engine and/or if the S/N matches what’s on the VIN plate.
 
Back
Top Bottom