Better brakes.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

You should look at the abs delete option to improve your braking. A 26 year old system is probably worn out.
If you want to keep the abs start with replacing all of your rubber brake lines and make sure the system is bled properly. Clean all of the abs wheel sensors and check the wiring. There are mixed opinions on using 100 series pads on the front. Like @flintknapper said our properly working system is pretty good.
 

@flintknapper knows the 80 and “proper operating condition” is the truth. The problem is bleeding all of the air from the complicated ABS plumbing system. Many have achieve better brakes by eliminating the abs system.

I went a step further and increase clamping force at the rotors with a hydro booster.
 
I went through the brake system on my 97 a few months ago.
New OEM rotors on all 4 corners.
Rebuilt all 4 calipers with OEM rebuild kits.
New OEM brake pads on all 4 corners.
Full brake fluid flush. Brake fluid is supposed to be water clear.
All soft lines were replaced with OEM when I got the truck in 2014.
Master cylinder was replaced with new OEM in 2017.

Riding on 315/75R16 Duratracs with a 4" lift and lots of "stuff", I can lock tires and activate ABS on dry blacktop.
 
Frozen Rotors, Hawk LTS pads, and Napa Eclipse Calipers have been great on ours. Massive stopping power. Will swap out the old lines next year to stainless steel when I change the brake fluid again.
 
@Jzelnick. Could you share the model/reference of the rotor and pad combo?
I just did the front pads on my 97' and I'm seriously considering doing an overhaul as @jonheld mention above on the next service replacement. Tipically, I'll go the extra mile to keep everything OEM, but if there's an after market solution providing a proven superior performance there's a good chance I'll pursue it
I was also looking at DBA rotors and Slee's brake lines
Cheers!
 
The brakes will never been as good as you want. Sure they can lock up etc...but of your trying to get new car breaks in a 20yr truck it just won’t happen. Bleed delete abs change lines if you’d like rotors and pads, guaranteed it’d be like that in the 1990s
 
I understand. It's a 97 and I'm not expecting a miracle. Just an improvement, whenever possible, over OEM. My expectations are modest.
Cheers!
 
I understand. It's a 97 and I'm not expecting a miracle. Just an improvement, whenever possible, over OEM. My expectations are modest.
Cheers!
I don't understand.
If I can lock up tires and activate ABS on dry pavement, what improvement in the brake system are you looking for? If the brakes can stop the wheel rotation and break traction, then we have achieved maximum brake performance. Where do you go from here?
 
@Jzelnick. Could you share the model/reference of the rotor and pad combo?
I just did the front pads on my 97' and I'm seriously considering doing an overhaul as @jonheld mention above on the next service replacement. Tipically, I'll go the extra mile to keep everything OEM, but if there's an after market solution providing a proven superior performance there's a good chance I'll pursue it
I was also looking at DBA rotors and Slee's brake lines
Cheers!
Heres my set up. This is what @JZelnick is
Speaking about. Front pads are for a 100 series LC,
Rears are for an 80. I ordered just the front rotors thinking id save a few $ and within a few days ordered the rears as well. Being cryogenically frozen helps ward off warpage. Stopping is better than prior. Did the slee full braided stainless kit. Stops my armored, 37’d truck to satisfaction. I did the abs delete too. Hope that answers your question.

5D1EB9DA-D608-40D6-9F78-06CCD1E8980A.jpeg


F6D61660-8574-4716-B026-4ED4123918F0.jpeg
 
I don't know when ABS appeared on 80's here in Oz. My 3/92 80 doesn't have it. I've done an upgrade on the front brakes, and run 105 series pads (currently 'RDA Extreme' brand) in the front. Haven't touched the rear brakes as they are already set up with disks not drums (apart from the handbrake, which is a 'drum brake' style on all 80 series.

Master cylinder is a factory one obtained new about 2 yrs ago. The brake booster is still the original one fitted ex-factory in 1992. Can't find new genuine of those anywhere.
 
Heres my set up. This is what @JZelnick is
Speaking about. Front pads are for a 100 series LC,
Rears are for an 80. I ordered just the front rotors thinking id save a few $ and within a few days ordered the rears as well. Being cryogenically frozen helps ward off warpage. Stopping is better than prior. Did the slee full braided stainless kit. Stops my armored, 37’d truck to satisfaction. I did the abs delete too. Hope that answers your question.

View attachment 2042414

View attachment 2042415
Thanks much for the info mate!
Looks like a good set-up for a happy cruiser head!
 
Back
Top Bottom