Media 200 series picture thread (30 Viewers)

[lmud]

New Rims, trying out machined finish since my last 3 vehicles had black rims. 18inch Method Mesh

 

[Angelo1]

I'm rocking the same wheel, +20 offset works great! MHTD55818905657

Thanks, any reason why you didn't go with 17's?

 

[kreiten]

Thanks, any reason why you didn't go with 17's?

I didn't see them available in a 17x9 5x150mm, or I proly would have gone that route

 

[SGT0311]

Do the 17" Method wheels fit a 200??? Has anyone tried?

 

[kreiten]

Do the 17" Method wheels fit a 200??? Has anyone tried?

somebody awhile back was rolling some 17's, I think they were methods... would proly just be a question of backspacing and fitting over the caliper, my guess is most 17's would work, just a guess...

 

[garymyman]

View attachment 1222582 Whoa

So the new 570 can look great... If you lop off the bottom half of the bumper. Wonder if that new ARB would mount up.

 

[vabluefish]

Just got my 200 last week. 2010. Love it. Coming over from a 4runner. Of course I'm deciding on a lift and tires at the moment. Got the front two windows tinted today.

 

[MScruiser]

I vote Ironman Foam Cells with BFG K02s in 275/70/R18s.

 

[vabluefish]

I vote Ironman Foam Cells with BFG K02s in 275/70/R18s.

The KO2s are pretty much a given! I had the originals on the 4runner and really liked them.

 

[shellb]

New Rims, trying out machined finish since my last 3 vehicles had black rims. 18inch Method Mesh

Looks great! Nicely chosen.

You mind posting up the wheel specs when you have a minute?

 

[dscully]

Despite frozen/stuck KDSS, got the TJM lift/ARB/winch on. Already had the 275/70/18 Toyo AT2s. The shop did a great job and the truck is level.

With a couple of it's new friends at the shop just before I picked it up.

 

[lmud]

Looks great! Nicely chosen.

You mind posting up the wheel specs when you have a minute?

They are 18x9, 5.75 Backspace. Had some rubbing on the mudflap so I removed those.

Mesh | Machined Face Truck Wheel

 

[MScruiser]

Despite frozen/stuck KDSS, got the TJM lift/ARB/winch on. Already had the 275/70/18 Toyo AT2s. The shop did a great job and the truck is level.

With a couple of it's new friends at the shop just before I picked it up.

There's always gotta be 1 wannabe in the group that ruins the picture (Land Rover)

 

[TRD Burglar]

I just got back from Moab. Here's a couple of pics from Moab

Baby Lion's Back

Top of the World

 

[shellb]

They are 18x9, 5.75 Backspace. Had some rubbing on the mudflap so I removed those.

Mesh | Machined Face Truck Wheel

Thank you!

 

[montanarally]

Thanks, any reason why you didn't go with 17's?

What size and and brand of wheels are those? Looks like Fuels...I would like to get the pet numbers and size for these so I can look them up and decide between yours and RW wheels. Also, what size tires are you running and do they fit without rubbing in a full turn? Great looking setup!

thanks! Ya as said they are fuel Venzas with bfg 34x12.50r18 . No rub but dam close lol I had to remove the front flaps because I drove down to Portland with the 34s on at stock hight to have the new lift put on very little rub after you remove the lower door trim plastic . fuel from what I was told dose not make a 17 inch wheel in the 5 lug pattern needed for the tundra and 200s

 

[kreiten]

painting gnomes, exploring some back roads and checking on my brothers Landy just to make sure it's in the exact same spot it has sat for the last 10 years... yep, it's still there

 

[ih8dirt]

Still old photos, but going on a new trip soon, so new photos coming! Going to test out new tires and the dual-fuel system.

 

[studawg]

View attachment 1219704

ooohhh, I see some old school Mickey Thompson Baja Belteds.....I like

 

[studawg]

Nah, needs a roof rack, sliders, winch, lockers, regear, etc.!

Nah, it has a roof rack. It needs the roof rack deleted to give it that slick top look!