1fzfe rebuild compression ratio?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 28, 2017
Threads
4
Messages
48
Location
Arizona
So I’m in the middle of building a 1fzfe out of my 93, pulled it because of a knock and ended up being piston slap. Caught it before any major damage was done but now I need to make some decisions. Already doing a cometic hg and arp studs but was thinking about upping the compression , I won’t be able to afford a turbo or supercharger in the future so NA it is... thinking about bumping compression ratio up to 10:1 and wondering if the stock fuel system will handle it and how far advanced in timing I’ll have to go, fuel octane etc. anyone with any experience in this area?
 
And I did use the search bar, nothing relevant did I find without a sc or turbo involved
 
Just plaining block and head to make flat then pistons to achieve compression
 
I don’t really have a number in mind.... more I guess would be an honest answer lol
 
I'm thinking if your looking for a boost in power by bumping your compression up by one number then you are going to be disappointed. Its just not going to make that big of a difference. The actual refreshing of your motor, new rings, having the head done, will probably make more of a difference then a small compression bump. If you are feeling a lack of power because of bigger tires or extra armor then maybe spend the money you would have spent on pistons on a set of TC gears or new R&P gears.
 
The ratio of dollar$ in versus horsepower out on the 1fz is not near as productive as it is for much more common motors like the Chevy small block. You can stroke it for some serious increase in displacement, but I think that was in the $5000+ range to get the whole setup??
 
@scottryana has lots of data on this, even though he has done primarily turbo setups.

Hopefully he will chime in here with the pros/cons.
 
@hazard is the one currently working on doing a naturally aspirated high hp build. There's a lot of info in there that is way over my head, I think maybe he has a degree in astrophysics or something.

Is that the same as Rocket Science? He's been goin WAY deep into motor tech!
 
Based on calculations a bump from 9.01 to 10.1 could theoretically net a 20hp (+/- 10) at the crank

Also its common knowledge in the racing world that hp gains of <20 aren't noticed in the butt dyno. So say you magically got 30 hp I still wouldn't expect it to measurably change the driving experience of a 6500lb cruiser.
 
Last edited:
That’s kind of what I figured, I just don’t want fueling and timing to become a head ache. I don’t have an issue running premium, the pig isn’t a daily driver . Power wasn’t really an issue before/during the knock, it had plenty until hills at highway speeds. I know these aren’t power houses but any improvement I can make while being semi stock is what I’m after. Gears are definitely in the future (after its running again)
 
I doubt you would have any issues with the minor increase in compression. I would imagine that by pulling timing you can get it close enough to stoich.

Rough calcs say You would need to mill the head down roughly .056" to achieve 10.1. I have no idea if the head is capable of handling that much shaving.

Looking through all the data you only stand to gain about 3-4% by bumping the compression to 10.1 which would equate to +6-8hp IMO hardly worth the cost.
 
Last edited:
You wouldn't do it by milling that would completely put your cams out of timing. You would have to do pistons with less dish.

The biggest problem like everyone keeps bringing up is the computer.

The way the maps work is like a big grid, you have a map for MAF voltage on one axis vs RPM on the other axis as a load table with adjustment done with closed loop narrow band O2 sensors.

So the Toyota engineers said the MAF is Xmm^2 and the voltage reading at this RPM means the engine is getting Ycfm air and the timing should be Zdegrees.

Now when you make big changes even naturally aspirated changes the engine is not in the same place on the load table and timing is not what it should be.

Will it work? Maybe. Will it work as well as it could? Nope. In my opinion the 1FZ really has to have some way to tune the computer if you are going to get any significant gains when naturally aspirated.


The only reason you can see 60-70hp gains from the TRD SC or home built turbo setups is because they are exploiting the open loop condition when the fueling is so rich you can add the extra air.




I doubt you would have any issues with the minor increase in compression. I would imagine that by pulling timing you can get it close enough to stoich.

Rough calcs say You would need to mill the head down roughly .056" to achieve 10.1. I have no idea if the head is capable of handling that much shaving.

Looking through all the data you only stand to gain about 3-4% by bumping the compression to 10.1 which would equate to +6-8hp IMO hardly worth the cost.
 
Back
Top Bottom