uca

Hey guys, Got a set of Nitro upper control arms brand new in the box for the 100 series. Asking $600. PM me if interested.

Hey guys I've got a set of brand new Nitro Upper Control arms still in the box. Asking $600 and open to offers. Thanks -James

Hey guys, Looking for a set of SPC racing UCAs for my dad's 98 lc. PM me if you've got a pair or know someone who might. Thanks James

Hey guys I'm looking for a set of SPC light racing upper control arms for my 98 lc. I've got a set of brand new Nitro Upper Control arms that I can trade. The SPCs are valued at around $720 brand new and I got the Nitros directly from Carl at Just Differentials for $750. They're still in the...

Stock UCAs off of my 2002 LX470 (taken off at 150k miles). I would recommend replacing the ball joints before installing them. Moving soon and need to get these out of the garage. Shipping is going to be about $30-50 depending on where they're going. Make me an offer!

Hi, I have a pair of used Nitro UCA's they come with new bushings. They are in great shape. $400 OBO + the ride. I believe they will fit in a Large USPS flat rate box (20.00?).

I've got these listed on eBay for $600 but will sell here for $550 plus shipping from 84117. Total Chaos Uniball Upper Control Arms Toyota Land Cruiser 100 Series 1998-2007 | eBay

I recently installed the new Delta Joints in my front UCAs. These replace the typical uniballs that Total Chaos designed for their control arms. This new joint is similar to the stock sealed ball joint, but offers more articulation. It has a small grease zerk on the top. You can use the low...

I'm looking to get the Lifetime alignment from Firestone since I'm making incremental changes over the year. Does anyone have any good/bad experiences with certain Firestone locations in the valley? Hoping someone knows of a good tech that's familiar with lifted cruisers.

Just got my “PolarBear” back from TorFab after hibernation with roughly 3” lift with the upper control arms and BP-51 and Budbuilt beefy .120 DOM and 3/8” thick steel rock sliders that is powder coated and aluminum armor plating stage 4 (front, engine, and transfer case). Next, rock warriors...

So there are a few reasons I am not very happy with my lift but two I was really not expecting this to be an issue since so many FJ's, 4Runner's, and now GX's have already been lifted. Lift Installed Used/Re-built 2.5 ICON Extended Travel Coilovers SPC Upper Control Arms Used 2" RadFlow Coil...

SELLING THE STOCK FRONT BILSTEIN COILOVERS, REAR COILS, AND UCA'S FROM A 2013 FJ CRUISER. ONLY ABOUT 15K MILES ON THE SUSPENSION PARTS BEFORE I UPGRADED TO AN OME LIFT. ALL PARTS ARE IN GREAT SHAPE, MY FJ CRUISER HAS BEEN BABIED AND HAS BEEN PRETTY MUCH A MALL CRAWLER. ASKING $180 FOR THE WHOLE...

I have a different thread about some things that I had questions about. This is one is just about installing the SPC UCA's. It's a one :banana: job imho Tools 1/2 drive torque wrench for: (1) ball joint top nut: 150 ft•lbf (2) ball joint stud castellated nut: 45 ft•lbf and then tighten to fit...

SOLD

Hello fellow mudders, I have a few things in my garage that have been sitting for a while, and I have decided to go a different direction with my truck so to the for sale section they go! Total Chaos UCA's: Price New $750 - Asking Price: $350 + shipping Used but in great shape. I bought these...

So I got my new UCA's in and am trying to understand how to get the top of the knuckle/upper ball joint away from the brake line and shock. I have the caster on setting D which they it says is good for 2-3 inch loft I don't understand the whole camber/caster settings. My plan was to get this...

Converted my 200 using Tundra parts to LT. So I have my Total Chaos uppers for sale. They've been on the truck for a year or so and have no rubs or damage. $500 plus shipping first PM gets them :) -Rich

Hey guys, I just installed a new lift, springs, and UCA's over the last couple of days. Finally put it down on the ground, and I have crazy positive camber on the front tires....they literally look like this \ /. How do i adjust for this? Is the UCA bolt orientation? Is it the torsion bars...

18 months in to these and they are sounding terrible all of a sudden? First 18 months were relatively squeak free... Any remedies? Really hate to go through the exercise to remove them.

We have some take off parts from land cruisers that we would like to clear out of the shop -Working AHC Suspension System, shocks, lines, coils, torsion bars, accumulators, pump, etc etc Fits 98-07 Lexus LX470 and some 06-07 Land Cruiser 100 series 2 available -2006 $700 -1998 $500 Couple...