rear

bolts up to where bumperettes mount. Very heavy, not worth shipping. Located in Roswell, Ga SOLD

I removed my rear bumper once but that was about 15 years ago, I remember taking it to a garage and asked them to remove the two middle top bolts. They just ground it off making scratches to the chrome. So I want to do it myself. They been soaking in penetrating oil for the past week. I...

I just found out that the 80 series rear wiper arm will fit my 1988 fj62. I'm looking for one. Anybody have one laying around?

Yesterday I decided I was going to see about putting some auxiliary reverse lights mounted to the stock bumper. After getting the cover of, I was very shocked to see the amount of rust. I knew one of the previous owners used the truck to take their boat to a salt water area, an apparently they...

I have a crusty rear axle from a LJ70, it should have 4.88 gears in it and is good for parts for someone that owns a LJ series Cruiser and wheels it occasionly to have some spares in case you ever need them. 150$ to get it out of my way

Hi Folks, Coming back from Mexico, the rear diff started engaging randomly. Pretty strange when you're going 60 mph. The central diff. does not come on. Just the rear. I had to stop at the shoulder and turn the center diff and rear and front buttons on then back off and it went away. Did it...

I searched and did not find one - Anyone have a good write up or video of motor and actuator replacement for a 2000 LX 470?

Rear shocks need to be replaced...they look wet, not too bad, but they've been that way for awhile. Truck feels like it has no shocks now, front to back. Tech says just to replace rears, but this sounds like a big no no if the XREAS system has lost too much fluid. Probably original 2004 shocks...

Total long shot but figure it couldn't hurt to ask - anyone have a top rear panel that is in bad shape other than the piece identified below? I'm going to try and repair but it is a pretty intricate piece with multiple curves. I drilled out the spot welds and cut at the pillar to remove. I...

Front axle is sold. I have a front and rear axle from a BJ73 with 4.11 gears in it,these axles are the same with as any 40 series and the only difference is the with of the spring perch mounts. Cleaning up the shop so they are priced cheap to get them out of my way,shipping can be done with...

Hey guys just like the subject says I need some help tracking down the brackets for the Japanese rear visor. I thought I was going to be able to be a little tricky and use 3m body adhesive tape but at the very least you need the lower brackets. I bought the visor from a mud member quite a...

From an early 80's BJ40 Great condition, other than the hard brake line 4.11 gears $500 picked up in Las Vegas, NV, or I can ship via Fastenal

Looking for a couple of passenger side fender flares in silver.(see pic attached) Shipped to 80550

Hi, I am looking for: Kaymar rear bumper with tire and gas tank carrier or similar. Old Man EMU Heavy duty suspension Full size roof rack. Please, let know if are selling any of this ones. Thanks Ivan De Lucia

I purchased the seatbeltplanet.com FJ60 rear retracting seat belt set to upgrade my 1987 FJ60 rear belts. The old lap retractors were old and jammed, and I want to be able to take along the whole fam on trips. Currently only 2 can ride with me, and one has to "ride bitch" using the rear center...

SOLD SOLD Selling a complete third member with a new Aussie locker installed. PO said it was never run and I believe it because the axle it was bolted in was not completely built and it looks really clean, has 4.10 gears. I got it with a project rig. Asking 300.00 for it plus shipping...

Looking for a mount if anyone has one they are not using. LabRak is currently out of stock. thx! Sean

Refurbing some interior items and was wondering if the leg portion that flips down on my jump seats should be grey in color? They are black now but I am not quite sure that is the color they were when new. This is the hoop shaped flip down piece-essentially the legs for these seats. Anyone...

I have read several great threads about options for adding rear 3-point seatbelts to early Fj62s. I can feel the hole where the upper would be bolted but I do not know if there is a retaining nut. I have not found a definitive answer on how early Toyota started installing the nut. My FJ62 has a...

Wanted: Four Rear Body Mounting Brackets (#1) TEQ part number 51741-60010. New, NOS, Excellent to Very Good Used for summer restoration and installation of a Aqualu 3/4 aluminum tub this summer!