rear

Hello. Does anyone know a part number or where to get just the rubber dust boots for the rear brake calipers? I can only find it in the rebuild kit. I do not need anything but just the dust boots. Any info or if anybody has any extra they want to sell let me know. Thanks!

2709321876

NO LONGER LOOKING, thanks! Looking for a pair of rear spring spacers. Don't mind if they are used if they are still in good shape. Let me know! Thanks! Looking for the Slee or Ironman spacers or the likes. Not interested in the cheaper Mr. Gasket rubber spacers.

Selling stock rear lights fj80 $140 great condition

I have a Hayman-Reese (2") tow bar and it is fitted to the BJ40 by bolting onto the chassis and uses the four factory trailer hitch holes in the rear bumper. See pic below. I want to retain the Hayman Reese towbar for use with normal tow ball hitches, but I want to be able to mount a pintle...

Hello, What is the best rear axle / rear end set up for a FJ60? I just ordered an ARB locker and 4.56 gears for my rear end and dropped my third member off at the shop to have it installed ($450 labor). Well I tried to order some chromoly axles and found out PP stopped making them. I'm...

A land cruiser friend returned this seat to me he had it in his garage for years and is not going to use it. I think I got it from a Mitsubishi Raider years ago it's in good shape and has gray cloth upholstery. Free to whomever can use it. Best to email em shmukter@pa.metrocast.net

Ben Delp returned this seat to me he had it in his garage for years and is not going to use it. I think I got it from a Mitsubishi raider years ago it's in good shape and has gray cloth upholstery. Free to whomever can use it. best to email em shmukter@pa.metrocast.net

I have this nice bezel that I was keeping as a spare. It had a bit of surface rust on the back side. I meadia blasted it and then primered and enameled it. It should last forever now. The front side chrome is in very good condition. The plastic toyo logo has a bit of fading in a couple spots. I...

Has anyone done this? Have any pictures? Including seat belts?

Hi, Mine is a '95 HZJ80 (Australian). Rear axle is full-float with discs. I was all set to do my rear wheel bearings on Tuesday (Anzac day holiday here), but got worried that I've been supplied front wheel kits instead of rear. Any one able to offer some advice before I start trying to force...

I've upgraded my suspension, so I have these factory UCA's from a 1994. I put new OEM Toyota bushings in them spring 2016, so they only have about 4k miles on the new bushings. Would be an easy swap for someone who needs new bushings. Located near Charlotte, NC. $50 for the set, plus actual...

I recently got my diamond plate covered rust eaten rear quarter panels replaced with new panels, but now have empty spaces for the side markers and back up lights that are long gone? Anybody have any that they would let go of?

Sold. Kelvin.

100 series Air Con pipe repair

$50 + ship :cheers:

I feel like I have looked everywhere to find new weather stripping for my 1967 FJ40, but found no such luck. I was able to find it for my 72 but recently discovered the difference in sizing on the hard tops. Does anyone have any suggestions? Any help is greatly appreciated.

These are original rear jump seats I removed from a 1972 fj40 I purchased. One is in good condition the other is in good condition however 2 of the bolt flanges need repaired. See photos. They are original and 45 years old. 300.00 for the pair.

i just put 2inch lift rear springs in the rear of my gx i had stock 4runner springs before. after i put the new springs in i noticed that the axel was an inch to the right. not sure if it was this way before or if i should be concerned. any thoughts appreciated. thanks

I swapped to hell fire knuckles. So I have the stockers. THey have new (but installed/removed) timken trunion bearings and both steering arms that INCLUDES THE OVERSEAS one for a front-side tie rod. I will ship them out for 200 to within the 48 states. OBO if its up for a while. REAR FULL...