pulley

Fits 75-90 2F, 3F, 3FE. Fresh powder coat. Quantity 1 available $95 shipped.

My wife started up the truck this morning and it was making a very loud noise from what I could hear over the phone. It sounded like the fan was hitting something. I just got a chance to look at it and I’m kind of seem dumbfounded. Not sure where the noise is coming from. I have noticed that it...

I recently purchased a 1982 BJ40. Looking to upgrade to power steering. I have all the parts except the power steering pulley and idler pulley. Anyone have one??

I'm doing an alternator conversion to a Chevy alternator on a '75 FJ40. Original Toyota alternator was using a 17mm wide (approx. 5/8") V-belt. Chevy alternator pulley is sized for a 3/8 V-belt. Where would I find a wide pulley for a Chevy alternator? I thought about using the pulley from...

I wonderingwhich way the four bolts that hold the clutch fan and pulley onto water pump come off .clockwise or counterclockwise. I having huge problems getting these off and no trouble which any other on truck I post picture of the fan pitch as herd that makes differance

Looking for 3FE Crankshaft pulley for a 92, not sure if the 60 series pulley is interchangeable but the part number is 13470-61030. The only one I found online is over $500-$750, which at that rate I might as well buy a new engine.

I've searched high and low for a 1992 crankshaft pulley and can't find one anything. Anyone know where you can get one? Or anyone parting out a 91 or 92 and willing to ship the crankshaft pulley?

Hey All, I'm about to replace the idler pulley on my 1996 TLC with an OEM part. How do I remove the original idler pulley? Just keep loosening the 14mm nut in the center of the pulley? Thanks.

Hello All, Been trying to remove a Pulley from the PS pump shaft. Is there a certain method or trick to this? I have done a search on here because I remember seeing a thread about it a few years ago but I cannot find it. I have also looked at the FSM but I did not see anything specific to the...

Been a LONG time since I've had an 80.....I bought this (From Landtank?) and never installed it. I came accross it the other day and have decided not to hang onto it. bracket and pulley as shown in the photo........make an offer?

Notcing my FJ60 2F crank pulley has a slight wobble to it (newly rebuilt engine, just installed the crank pulley for the second time after recent rebuilt motor install) Is this amount of wobble normal? see video I also noticed the engine is sitting at a slight angle to the left, and am...

I have been dreading replacing this seal for a while, so I will tackle this project in the winter and document it. I have had difficulty finding clear instructions on replacing this seal while the engine is in the vehicle. I understand I need to remove the radiator, bib, etc., so I have room to...

Came off my 1972 F engine. $20 obo

My v-belts were shot so I bought some replacements from Toyota. First time changing belts, but how hard can it be? Went to pull the old ones and had a hell of a time getting them off because whoever worked on it last routed them OVER the idler pulley. Highlighted in the drawing here. The FSM...

I'm fabricating a custom cruise control set-up in one of my rigs and I'm looking for a Cruise Control Throttle Body Pulley or Auto Trans Kick Down Pulley off of pretty much any Toyota. Pretty much the only requirements are that it is metal not plastic and the smaller throttle barrel size...

Looking for a double water pump pulley for a 78 2f

2004 Tundra, high miles 370k, just purchased and pretty much have everything buttoned and running well. Notice a coolant leak coming from front of engine. Long story short there is a gash on the back on the main coolant hose that looks to have been created by it coming in contact with the...

I will be completing a 79 BJ40 & am looking for styles of pulley removal systems for topless operations. Constructed with removals in mind. Safety tip or suggestions are as always, greatly appreciated.

Hello, I'm looking for either a three-groove pulley to run a York 210 off the 1FZFE, or I can take an entire kit of someones hands. I'm hoping someone has one lying about they haven't installed, or no longer wants theirs etc. I reached out to Joey and unfortunately the pulleys probably won't...

Stock pulley, no issues. Keyway doesn’t have any damage and bore is clean. $55 + shipping