door

NOS Toyota mirrors part #87901-90300. Measure 5 3/4 inches. Perfect NOS condition. $125 shipped SOLD. Please reply in thread. Thanks, Dennis

After struggling to find Saloon Door latch pins for 40 series in good shape for a project it was suggested that I make my own. Here’s what I ended up putting together. In kit form, I upsized the threaded pin to 6mm for more strength from bending at its connecting point like the factory version...

Tiny clamps, one section at a time. Start in the upright position and do top of doors, then lay flat to do bottom in the same manner. Lay generous line of adhesive. Helps to lay gaskets out overnight on the door with a heater on the night before.

When I turn sharply right, the doors unlock and the dome light turns on briefly. I can also hear a long peep. I suspect some sensor on one of the left doors. Any clue or experience? Thanks

Update: cleaned all connections and applied dielectric grease at passenger side kick panel and everything is up and working. There was no sign of water intrusion but i did install a roof rack and new Windshield and will look into those places. This morning my key fob wouldn't open door. I...

Hello- 2000 Land Cruiser right rear middle door hinge has torn off on the door . The door opens and closes but the middle hinge / support bracket is what provides resistance and keeps it open etc. Somehow it has torn out... See photo. Is this issue " common " with the 100 series? The biggest...

These are upper, removable front door frames for 7x vehicles. RH/LH. Great for those with removable tops. $300 + shipping. OBO.

Had rust on bottom of door so cleaned it up, hit it with self etching primer, then Bondo and then thought to myself...opening and slamming all the time will probably make Bondo crack and fall out so painted over it w/ Herculiner which hopefully will hold it all together. Any thoughts?

Hello, my door ajar light won’t turn off and I’m traveling on I40 towards Nashville. It just went on. I stopped and checked all the door sensors and it still doesn’t turn off. I’m worried it’ll kill the battery overnight so plan on disconnecting the battery at night till I can find the...

So I've ordered a set of Rhinohide Armor panels and they will not work with the stock lower door trim panels. My options are trim the Rhinohide panels or pull the OEM lower trim panels off. If I do the later, I'll be looking at this: So how to best fill the holes? There is no easy access to...

If anyone can find me an 80 series LH front door armrest base in oak color I would be incredibly grateful. Thank you!

I am in need of an 80 series front driver door card badly. Thank you!

Wanted to share this here. Has to do with Door Panels

Nice original chrome! Will clean up nice. $125 shipped!

Drop area is flexible. It's a door shell for an 80 series.

Good morning! I am a new FZJ80 owner and I cannot close my driver’s door very well from the inside because the handle is broken around the area where it connects to the screw that anchors into the door. I will happily take any color, but oak is preferred. Thank you, Nick

has anyone figured out the cause of the wind noise at the top of the driver side door? i've seen other threads of people having luck replacing the door weatherstripping so i just replaced the front and rear driver side door weatherstrips, which cost me $180 for the pair and while the doors seam...

My front door cards came with speaker holes cut in courtesy of the previous owner. I managed to swap them for a pair of unmolested but shabby door cards. On the 'new' door cards, the vinyl covering is pretty much perfect, but the fibreboard (not sure what it's called in the US) is warped and...

Based on a referral from a trusted Land Cruiser shop in CA, I pounced on purchasing a pair of NLA OEM front door lock actuators from this vendor on ig for $800 USD shipped. @binmahmoodstores Communication was great. Packaging was great. Delivered in a reasonable amount of time. All good...

The door keeper binds and rips from the metal of the door. A backplate is needed to strengthen the area for the new door keeper. I've seen repairs where the door is completely disassembled and angle iron is welded inside. But I've also seen some where they simply bolt a plate to the door; 2...