Hello everyone,
I'm looking for 20mm front proload spring spacers. Westcott would be a good option if my goal was to achieve a higher lift or needed the additional preload, but I don't.
Concept:
BLUF: level LX570 with a 1-2 inch lift with OEM suspension characteristics.
Front
Add 20mm front...
Hi folks, My first post here.
I have a 2004 GX470 with 130k miles on it. I have been having some passenger side intermittent air height issues and am getting ready to install a passenger side rear height sensor that I bought a few weeks ago. Specifically, the passenger side will drop very low...
I have the C59-535 coils installed but gave me more lift than I was planning on. Would like to swap for the c59-559V if anyone is interested. Or purchase if anyone’s pulled any off. Located in Austin, TX.
Both in good working order taken from a 1997 LX450
ECU 89661-60650 - $200 shipped
MAF 22250-66050 - $60 shipped. ***SOLD***
Ignition Coil 90919-02209 - $50 shipped
$100 + shipping
I bought this off a '99 100 series that I have been buying parts from at a salvage yard. Cruiser only had 178k miles before it was hit from behind and totaled. Was definitely holding pressure when the knuckle head removed it for me and released the refrigerant into the air. I...
Looking for an AC evaporator coil for parts, doesn't need to work or can have leaks. Just the coil and connector fittings, don't need the housing. Shipping to 28461.
Have a dizzy and coil off a 87 FJ60. Bought for my FJ40 but never installed. Came from a running engine.
Located in Chattanooga, TN
$250 plus shipping.
I could use some of your expertise and guidance please about the rear coils of an 03 limited sequoia 4wd. I installed 1.5” rear spacers in conjunction with bilstein 5100s. I have confirmed that the shocks are not limiting travel bc as I jack up the frame, there is room for the shocks to travel...
Did an engine swap in my 80 series so I don't have a need for a lot of left over OEM parts
Ignition Coil for sale, no issues when I pulled the engine. $75 buyer pays shipping.
Trying to dial in your rear suspension height after a change in setup? Adjust for weight on one side vs the other? I used the smaller ones to adjust for gas tank/rear tire carrier lean. The 30mm spacers are about 1 - 1.25" lift.
I am selling a group of spacers that are just for you!
2x 30mm...
Up for sale is a set of Old Man Emu 2.5" Front/Rear coil springs for 1991-1997 80 series Toyota Land Cruiser.
These are 2.5" Medium load springs.
Part #s OME2851/OME2860
The front and rear springs are used and were purchased in 2019 and removed in December of 2022.
$300.00 for the set of 4...
Installing 2.5” lift. Loosened kdss valves 3 rotation and LC is on 4 jackstands. Rear install of shocks/coils/airbags went fine. Using OTRAMM video as my guide but encountering problem up front getting ball joint loose from upper spindle. (Circled in red blow). Nut came off fine but not able to...
I am starting an FJ45 project and there is a coil with an external ballast resistor. I am thinking of getting a new coil with an internal resistor… not being well schooled in ignitions, what happens to the two wire that are connected to the external ballast resistor right now?
I get a few drops of coolant behind my rear drivers side tire when I do short low speed drives around town. I top up coolant once a month no more than a half pint. Hasn’t been much of a problem this summer but cool temps are coming. I took it to someone to check it out and under pressure the...
Brand New in the box "Southern Offroad" Air to Coil Conversion kit. If you're looking to convert your GX470 rear Air Bags to Springs, look no further.
The best and only GX470 airbag to coil conversion kit on the market with height adjustability.
It allows for 3/4″ to 1 1/4″ inches of lift on...
Brand New in the box "Southern Offroad" Air to Coil Conversion kit. If you're looking to convert your GX470 rear Air Bags to Springs, look no further.
The best and only GX470 airbag to coil conversion kit on the market with height adjustability.
It allows for 3/4″ to 1 1/4″ inches of lift on...
This regards my 1988 FJ62 with original 3F-E engine.
I've been running through the electricals trying to determine why the engine cranks beautifully (and I smell gas so I believe it's not a fuel pump issue) but I get no firing. No sparky at plugs; no voltage at igniter wires as they enter the...