bj74

im in need of a kickdown cable emailed a few company that make custom throttle cables and the were not to sure if they could help me. has any one used the hz to a442f kickdown cable "35520-60060" in its replacement the 3f to a442f is a bit to short and will not work if some one has one in the...

Will someone with a 74 two door take a couple measurements? -Roof top front to back, and side to side. -Rear floor from front of rear seat cushion to back of front seat. -Rear floor from back of rear seat to back door. -Rear floor from back door to back of front seat. Please and thank you!

Really need some help here, Been chasing this problem for about a month. When I turn the key off, the truck drops down to about 200rpm but will never shut off. I have replaced the VSV, all the vacuum lines, the Venturi, and made new gaskets for the Venturi and intake heater. The vacuum pressure...

Hey there, this is my first post in this forum. I've found myself here several times when looking for answers to my BJ74 questions so I figured I should just join. I'm so grateful for the wealth of info and knowledge in this community. In September last year I finally bought a BJ74! A short...

Hi everyone, My first post here. I am currently trying to fix a starting issue on BJ74 - 13BT. When try to start the car, it doesn't turn over. All lights come on inside the and i have recently replaced the battery and starter relay unit behind the battery. I have also tried hitting the...

Sometime early last year, I picked up another truck from my good friend @joekatana. It started life as a 1989 RHD BJ74. Over its lifetime, @rick_d converted it to left hand drive, dropped in a 1HDT or two, and added a few more things. It made its way to Joe, and then to me. Joe did a bunch of...

Gents, I have a center console and rear heater out of a BJ74 for sale, in working condition when pulled but it does have a dent at the end of one of the coolant lines that I made when pulling it out. May try to straighten it back out soon. $300 OBO, can ship USPS through my APO, so it’ll take...

With the BJ74 sold, it’s time to sell the armor set. I was so excited about this stuff but in the end it wasn’t meant to be. Front bumper includes hoop, rear bump includes rocker protection hoops and weld in hitch. No swing out. Sliders are 68”, perfect for a MWB Cruiser. All together this is...

Hi all, So I’m currently working on a BJ74 which previously had a 13BT fitted, the original loom was cut when the original engine was removed, added to this I’m now trying to correctly fit and wire in the 1hd-t that the PO started installing. I’ve got it all sitting correctly and running...

Hey all, I'm about to register my California registered BJ74 in Colorado, at which point registration it currently has may not be able to happen again. I am putting it up for sale at a premium, price is non-negotiable. I did a lot of work to get it registered, and I have received renewals from...

G'day gang, the BJ74 has been a little neglected as of late unfortunately due to moving states and being unemployed for a period of time - now that I have the time and coin I would like to start fixing it back up. A few things need attention but I seem to be struggling to source the...

Hello to anyone reading along here. Well where should I start... this is my first time posting pretty well anything of significance online so please bare with me while I figure this all out haha. 2 years ago I made the move from the prairies of Saskatchewan, Canada to the magnificent coast of...

Hi, I have a 13BT engine which needs a rebuild as one of the piston chipped on the edge. I has the gearbox with transfer case and also has the PTO attached. The gearbox is still in good condition. Comes out of 1988 Toyota BJ74. Done 250.000km. power steering and alternator rebuild by previous...

hey everyone this is probably a dumb question but is there any way to adjust the rev limiter in a toyota 3b and/or a 1hz? cheers

Hi: Need a bit of assistance if anyone has any time. Looking for a picture of an OEM, non-molested fusible link preferably from a 24v 7x series truck. It would be on the positive terminal of the "positive" battery-- one closest to the firewall on the LH side. You would need to pull up the...

So I broke the internals of my temperature adjustment for the AC/heater when trying to adjust the heat - I'm guessing a combination of difficult operation and brittle old parts in the dash - and can't get the replacement fully installed. It's one of the first things I broke when I got the car...

Hi all I have a question about brakes. My 74 Land Cruiser has a funny feeling pedal it goes in really easily for half the travel and then is basically Rock Solid. I've tried pretty much everything I can think of. I just put a new master cylinder in from an 80 series replacing the old one but no...

I'm selling my 1989 Toyota Land Cruiser BJ74. It's great, but it's time for it to find a new home. Right hand drive, 5 speed manual, 3.4L turbo diesel, selectable 2WD/4WD high and low, lockable front hubs. It was my daily driver in Japan for the last 2 years until I imported it back to the US...

Hey all. So I found myself in the unknown after chasing my clutch fluid disappearance to my clutch master after replacing the slave (may or may not have been needed), and right after that discovery, my truck stopped shutting off. It was then I discovered it has a clutch booster, something I...

Hello, just purchased a bj73 , 1985 3B body has no rust and interior is quiet clean. Exterior paint is not bad, few scratches, Engine has 600,000kms though. Wondering what a rough price for Australia would be.? Has a bulbar small tyres, spotlights roof fack just general small things.