I hosed my front axle birfield by hammering it home with a sledge to seat it in the new oil seal. My new oil seals are very aggressive and I had to hit it hard, slightly mushrooming the end of the birfield, making it worthless. All my fault, dumb mistake.
Anyone have a used one sitting on a...
Toyota Land Cruiser 60 Series Rock Sliders. Great shape overall. Previous owner had them coated in bedliner. Shipping can be accommodated at buyer's expense. You will need to source some new mounting brackets as the originals are welded to my frame rails. These appear to be from: 4PlusProducts |...
I'm looking for a picture, if possible, of one of the PTO drive shaft pillow block brackets from a late 60 Series.
There seem to be multiple arrangements of drive shafts and brackets. I'm not sure when the change occurred, probably late 87 with the facelift, but I have seen an early (1984ish)...
Tow hitch (tow bar) for 60 series, it’s heavy, come pick up in Los Angeles or I will be in Las Vegas and Tucson Arizona in May and could bring it with. $100
https://www.cruiserworld.eu/shop/60-series-en/bumpers-chassis/tow-bar/?lang=en
Can anyone tell me if the factory 70 series 16" chrome wheels will fit a 60 series wagon?
I'm hoping to mount these with some studded tires for winter.
https://cruiserteq.com/steel-wheel-fits-16x6-4x-5x-6x-7x-applications-whl60262/
Looking to eventually Re power my 60. Seems the most common are LS V8s or Cummins R2.8s. I’m wondering why I don’t hear of using more modern six cylinder’s like the Toyota 3400. The Jap made version in early 2000’s tacomas was an excellent motor. US version not so much. Another choice might be a...
Hi everyone,
Not a frequent poster here, but a very frequent visitor. Currently doing a 1hdt swap on my 86 fj60. Here’s some details of the engine before I get to my issue:
Got the engine from a user on mud who shipped it over to the states from another user (both are frequent and reputable...
"Nancy" the TLC is going up for sale. I have her listed on eBay Motors as well. Just under 180K miles on the frame. A440 transmission and original transfer case rebuilt at around 176K miles (completed by AAMCO). Interior is clean. Aftermarket stereo with front USB input. Rubber floor mats...
For sale, 60 series ring and pinion. Front set shows little to no wear at all, rear has 230k miles, looks polished on the teeth, one chip on the pinion end. Both ran great with no issues, I re-geared and like the new ratio with my setup. Missing most of the carrier bolts. $300.
EDIT: Top...
So...This is a project I was forced to. We bought the 1985 FJ60 in 1990 as a family car with 90K miles for $6000. Family trips were two weeks in the wilderness doing off roads and camping in BLM and NF. In 1994 we took it to the Arctic Circle with a 9 years old boy, two girls 5 and 3, and an...
Reservoir is in great shape, pump runs strongly, no cracks, original cap snaps tightly in place.
https://www.ebay.com/itm/134744835212?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=XWUprgkcTOe&sssrc=2524149&ssuid=XWUprgkcTOe&widget_ver=artemis&media=COPY
I'm looking for a manifold that fits the airconditioner compressor for a Denso 471-0204. This is supposedly an OEM part off of a 60's series, although I have put it in an HJ47. I have a working compressor, but no manifold to be able to connect the rest of the equipment. Any assistance would...
Hi All -
Have any of you converted your 60 series steering box to the 80 series? Then, has anyone further upgraded to the 105 sector shaft and pitman arm?
I have a 80 series steering box on my 60. Wondering if it is worth the $600 to upgrade to the 105 sector shaft and pitman arm? I do not...
I aquired a 1984 60 series with a chevy 350 TBI the 4 speed tranny with a ranger III overdrive. it is noisy even after changing oil in tranny, transfer case, and overdrive unit, also acts like sycros are needing replaced, parts as far as I know are no longer available for the ranger and...
Figured I’d throw these up here in case someone wants to move a shackle mount, undo a shackle reversal or upgrade their 40 to larger 60 bushings…
Full set of 60 spring and shackle hangers cut cleanly off the frame
$150 for all plus shipping
Or $75 for each end