Recent content by NikP

  1. NikP

    How do you balance a parking brake drum?

    Vibration happens with three sets of tires and different wheels. It happens with three different driveshafts. Because I have a triangulated 4-link in the rear I can easily adjust pinion angles, so I've had a traditional driveshaft in with the pinion angle matching the transfer case output...
  2. NikP

    How do you balance a parking brake drum?

    Yes, it's phased properly and balanced with the current phasing. Double checked at local shop.
  3. NikP

    How do you balance a parking brake drum?

    Not really sure. That's where I'm stuck. My front driveshaft angle doesn't allow me to get up to highway speed with the rear removed and not have another set of vibrational issues. I just run the 4wd at lower speeds but as best I can tell with the rear removed things are relatively smooth...
  4. NikP

    How do you balance a parking brake drum?

    New tires... balanced. No play at diff and pinion nut is tight. Vibration goes away when in neutral so it's drivetrain related. Smooth with rear driveshaft removed and running front drive only. Driveshaft angles verified by Tom Woods and a local shop. I have a 4-link rear suspension so I...
  5. NikP

    How do you balance a parking brake drum?

    I have a vibration on acceleration and deceleration between 35 and 50 mph. I've had the driveshaft balanced and checked multiple times. It's a relatively new Tom Woods driveshaft so all the joints are good. I've swapped in another driveshaft with the same result. I have new ring and pinion...
  6. NikP

    Who’s running K03s?

    I'm around 10K miles in on the K03. I love them for the reduced road noise compared the the Nitto Ridge Grappler's on the car when I purchase it. I've been back to DiscountTire 3 times for balancing as I have a slight vibration/hop above 50 miles per hour. They force balanced and rearranged...
  7. NikP

    Can the transfer case output shaft be swapped while in the vehicle?

    I've been chasing a vibration during acceleration and deceleration around 30-50 mph. The vibration is consistent with two different drive shafts (double cardan). I've had the driveshafts balanced and still have a vibration. My angles are all good - trust me I've studied this for years and...
  8. NikP

    What's leaking under my LC200?

    Appears to be coolant... too transparent to be transmission fluid. I can't tell where the picture is taken from but I would start with checking for a valley leak.
  9. NikP

    Why does my 2013 LX570 fusebox look like this?

    That's a lot of work and it doesnt' change the fundamentals of where you currently are. You had a working AHC pump despite where it might currently be connected. A constantly running pump would point me to start at the pump. Start by checking if you have power at the pump, if you do then...
  10. NikP

    Metal Tech Slider Install

    It's not clear what your issue is, but first off, the rivet nut has to slide into the hole you drilled. You might need a bit more clearance. If it's a function of your tool won't fit into the confined spaces then do an internet search for how to installed a rivet nut without a tool. A bolt...
  11. NikP

    Possible gas can solution: seasucker rotopax?

    One mount one each side of the vehicle. One 3-gallon can on each.
  12. NikP

    2008 with P0305 code.... aaarrgh.

    Not sure what may have happened with the injectors, but an injector might be part of the issue. Did the code come before or after the injector install? Sounds like you had some trouble there which is suspect. I'd also swap the #5 coil with another hole just to eliminate that possibility.
  13. NikP

    Possible gas can solution: seasucker rotopax?

    I have buddy that runs two 3-gallon Rotopax on a Seasucker mount on the rear windows of his Jeep JL. We traveled 8-days in Death Valley in January and he was constantly attending the mount sliding down the window. It also fell off twice during the trip. I'm thinking about a similar mount...
  14. NikP

    TPMS ECU Failed?

    I have a 2010 FJCruiser. Codes C2181, C2182, C2183, C2184, C2185, C2191 and a flashing TPMS dash light. All this leads me to believe the TPMS ECU has failed, otherwise it's coincident that all 5 sensors failed at the same time. I've read a few things. One says press the TPMS reset...
Back
Top Bottom