Recent content by Fast Eddy

  1. Fast Eddy

    Hot off the presses! 3/16" thick rear fender protection panels

    My extended rear shackles are from Mark's off road.
  2. Fast Eddy

    Hot off the presses! 3/16" thick rear fender protection panels

    If you go with Alcan they can make whatever you want and they aren't too expensive. They can put the pin where you want it so you don't have to drill your axle perches. Find someone with a lift kinda like what you want to make measurements and then adjust those measurements a bit to your...
  3. Fast Eddy

    Hot off the presses! 3/16" thick rear fender protection panels

    🤮 You should make the effort to drill another hole in your spring pads and move the axle back a little. If you were really motivated to do the driveshaft work you could get some new springs and move it 2-3".
  4. Fast Eddy

    Hot off the presses! 3/16" thick rear fender protection panels

    @todt, @Darkwing58, @Hugh Heifer, @hey you, please post some pics when you're doing your fittings. These spring clamps work great for moving them around. Measure 3x, drill once. ;)
  5. Fast Eddy

    80 series fuel pump or fuel pressure regulator issues

    It's stamped 1951 Denso in raised letters in the plastic and 02 11D 30-6990 in silk screen, both on the end bell. RockAuto: Part Number Part Type Price EA Core EA Quantity Total 1997 TOYOTA LAND CRUISER 4.5L L6 DENSO 9520008 (952-0008) Fuel Pump Strainer $ 7.27 $ 0.00 1...
  6. Fast Eddy

    Possible Group Buy - Flat Steel FJ40 Rear Fender Protection

    Shipping: 43x28.5x1, 24lbs Fedex cheapest to @Hugh Heifer in GA is $65. PM me your address.
  7. Fast Eddy

    Possible Group Buy - Flat Steel FJ40 Rear Fender Protection

    4th set spoken for. I'm going to get one of the good counter-sink bits to finish off the holes in mine. We can mail it around to complete the one hole in each piece that doesn't get drilled at the shop. It's in this thread somewhere, but as a reminder, one hole on each side doesn't get...
  8. Fast Eddy

    Possible Group Buy - Flat Steel FJ40 Rear Fender Protection

    Going to Tahoe and the Nat'l Forest from tomorrow to next Thursday, so hopefully shipping Friday. (?)
  9. Fast Eddy

    Possible Group Buy - Flat Steel FJ40 Rear Fender Protection

    The top of the plates are roughly at the fender join. The bolts are just below. I can measure for you sometime today. Edit: 5-5/8" below the top edge of the flat part of the fender, where it starts to bend inwards. If your fenders are not showing light through to the inside of the tub, above...
  10. Fast Eddy

    BaT CO: 1987 BJ75 Troop Carrier with 59k orig. miles.

    Makes me want to throw a good paint job, new hides and new running boards on my 122k mi 40th anniv and let it have a turn up there.
  11. Fast Eddy

    Possible Group Buy - Flat Steel FJ40 Rear Fender Protection

    I asked for status Wednesday. They said they were still waiting for the steel and would let me know when it was going to be in. I'll update when I know more.
  12. Fast Eddy

    BaT CO: 1987 BJ75 Troop Carrier with 59k orig. miles.

    Still a screamin' deal. Surprised BaT isn't bidding it up higher. I guess the bids will come in the end. I only ducked in here to post it. CA won't let me buy it. :( I mean register it.
  13. Fast Eddy

    Pismo Turf & Surf 2021?

    Hope it's Nov 4-7, Th-Sun. There are three spots available on Friday. Saturday is booked.
  14. Fast Eddy

    For Sale  NorCal: FB Market: '71 FJ40 Original Red Paint, 3-on-the-tree

    No affiliation. $19k.
  15. Fast Eddy

    SOLD Sacramento, Rock Crawler $15,000

    Wow. End of an era right there. Still sorry about the time my dog bit your dog. :(
Top Bottom