The inspection window is very small. You have to watch what's going by as you are turning the engine over by hand or by rolling the tires. If you are rotating the engine in the same direction that it runs (clockwise), then you would look for...
I would recommend removing all the spark plugs. with them removed, I am able to turn the engine by putting a socket/wrench on the alternator pulley bolt. This bolt is easier to get to than the crank pulley and you can see the timing marks while...
I've never been able to access the idle mixture screw with the air cleaner on. I usually take the air cleaner assembly completely off the carburetor and set it aside with the vacuum hoses still connected (air injection hoses have to come off...
I had ONE vehicle with this problem. IDK if the machine work or dimensions were the problem with the adapters, but just attaching the R134 couplers on damaged the Schrader valves every time. I've used adapters on other vehicles without problems...
It’s been obvious that the Schrader valve is leaking once I disconnect the manifold gauge adapter. It is like the Schrader valve is not closed at all. Google AI told me that the primary seal is the cap (there is an o-ring in the cap) but the...
I removed the Schrader valves from the R12 fittings so there are only Schrader valves in the R134a adapter fittings. When I did the first recharge after the conversion I added refrigerant to the high pressure side, per the body and chassis...
So last year I converted my A/C from R12 to R134a refrigerant. I built new hoses and changed the drier, the expansion valve, the thermistor (still available from Toyota),etc. I did not replace the compressor or the condenser or the evaporator. I...
So yesterday evening I received my Aisin Fan FNT-022 and Aisin Fan Clutch (FCT-017) for my 1985 FJ60. I purchased these parts on Wednesday @ 10pm central time, and they were delivered on Friday to SF Bay Area at about 8pm local time. a 48 hour...
Yeah. Don’t buy parts from Amazon. They don’t care. Saw a video recently as to why some parts are good and some aren’t when buying from them.
Take fan clutches. They buy them in bulk from all over; OEM suppliers and counterfeiters alike. They...
UPDATE: well my Amazon purchase of an Aisin FCT-017 arrived and the coupling on the clutch doesn’t fit my water pump pulley. The picture on Amazon shows that the coupling is colored red, as is the original, but the one I got from Amazon has a...
Yes. That was my backup plan, but when I checked on Sunday, Amazon delivery to me was after I leave from my October 10 trip. So when I get the new fan clutch (from amazon, later today), I'll install the old fan, then when I'm back home, I'll...
Thanks in advance for your advice. I'm in the process of replacing my fan coupling. I've got the fan and coupling out of the truck and I'm just waiting for the new coupling to arrive in a couple days. My old fan has been working fine (from day...
Unfortunately for me, my leak got worse by my trying to make it better. The leak started during my ownership, and besides having a reputable mechanic replace the pan gasket 20 years ago, I was the only one that ever changed to oil. I don't...
Recently I've been doing something like lead head. If you go to the Online Parts Center for Toyota you can select your local dealer. I've found that in my area (SF Bay Area), if the parts are ordered online for pickup at your local dealer, they...
Success! Thanks for everyone's help. I got the new pan and gasket on and so far no leaks. I was living with a leaking drain plug for years so it's nice to finally have my garage floor dry, at least under the oil pan!
I ended up using both the...
I don’t see any issue using a gasket that has residue… it will have FIPG on it again, right? Maybe share a pic of where it is.
I did my oil pan not too long ago. Also on my back in the garage. I think I tied the gasket in place with string or...
Thanks for the great suggestions, guys. I did a dry fit this afternoon using both FelPro Snap Ups and the studs that are shown in Georg's thread linked above and also mentioned by KLF. I put the snap ups at each corner and this help me get the...