What have you done to your Land Cruiser this week?

[hatman406080]

ready for sandblaster/ powder coating.

 

[handcannon]

This week not to a bj or fj worked.To be a mustang from 1966 v8 , 2 month ago bought in usa and ie is now ready.Sorry is not a land cruiser, but wanted to let him see
Greetings from belguim

Wow, that sure takes me back a few years. Beautiful!!!

Don

 

[DomsFJ40]

[/ATTACH][/ATTACH]t the Trollhole carb on and engine desmog. And that pesky ALT sorted out.

 

[todt]

Almost done welding on 82 and for some instant/quick feel good I put a GR starter on my 69(nice).

 

[pb4ugo]

Never rely on the stock parking brake... I set the brake once. It was holding fine. Got out of the truck. It started rolling back down the steep hill with a passenger in it and me more or less beside it. I almost got squished before it stopped rolling. Always take precautions.

That happen to me too. The 40 almost went over a cliff, w/a passenger in it. Fortunately the rear tire of my 40 just barely hit the rear tire of another vehicle and stopped it. It was just a matter of inches from missing the tire. After that, I rarely use the Ebrake. I always turn off the engine and put it in 1st or reverse & usually put it in low range. I figure 85:1 should hold it. Or I park in a way so it can't go far, if at all, w/it off & in gear.

 

[MicahMan]

Re did my buddies seat

 

[rope]

Pulled out my D-max, too much snow in the yard for the GMC, but the 40 had no problens.

 

[Hangtowncruzr]

Completely blown apart, painted, and time to finally start final assembly

 

[chicago]

A little over 2 years ago, I started some half doors... Got one done and finish welded back then, and the second one cut and tacked in. Today, I capped it off and finish welded it!!!

 

[Sheck44]

Started some painting

Finally after 2 months of prepping, fabbing new front sections of the wheel wells,welding and sanding the interior ...started some painting on the 66'

http://i264.photobucket.com/albums/ii200/SCOBRA48/BIG Blue/caccoon.jpg

http://i264.photobucket.com/albums/ii200/SCOBRA48/BIG Blue/photo-12.jpg

 

[juanchogaviria]

Installed the new winch, painted the grill and new emblem...

Juan
1970 fj40
1978 fj40
1994 fzj80
1982 fj43 (sold)

 

[Strait Cruisin]

A new upper dashpad. Thanks Beno!

 

[Huroneymoose]

Took it apart. Took it apart some more. Put it back together. Drove it.

 

[offrdon2]

Threw money at my cruiser

I received and installed two door cylinder locks, inside door paddle, window regulator, and still have a driver's side mirror to install once i remove rusty old windshield screws.

 

[coleman2347]

Installed Brakes and tires

Installed 70 series brakes, mounted 35's, and test fit

 

[Cdaniel]

Better get that off of the table before mama comes home!

A new upper dashpad. Thanks Beno!


http://i232.photobucket.com/albums/ee184/mommadie/dash.jpg

 

[Eshu Elegua]

 

[Roboosfj40s]

Adjusted brakes, drums all around, replaced rubber brake lines in front, painted oem round mirror arms and backs, installing lower dash pads. Cussed a liitle adjusting front brakes

 

[TCSTARK]

A little over 2 years ago, I started some half doors... Got one done and finish welded back then, and the second one cut and tacked in. Today, I capped it off and finish welded it!!!

Awesome!

Sent from my iPhone using IH8MUD

 

[Weber Sarge]

I actually drove mine today, that was good enuf.
Sarge