Water Pump '78FJ40

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 18, 2013
Threads
234
Messages
5,365
Location
Prescott Valley, AZ
Pump1.webp
Pump2.webp
Pump3.webp
So it is time...just started to weep at the front bearing by pulley. Ordered up the right Aisin pump from SOR.......ouch!!!! Anyways when I removed the old pump I noticed only 3 bolts were holding it on!!!! Thanks PO's!!!! Was missing the bolt at the 5 0'clock position....threads a bit buggered sO I will clean it up with the tap. Does anyone know what size metric and thread pitch for these bolts? Also torque spec when bolting on the new one???? One other question....when I apply the permatex to the gasket on both sides do I cover the entire gasket, just around the block hole or around the entire perimeter of this gasket??? Sorry for all the questions but this is the first time I have replaced a water pump. Thanks in advance! Pics below. Interestingly enough my rig did NOT come with an oil cooler and no sign at oil filter of the triangular bracket that was there for models that came with it so pump does not have the connection. Is that weird???
 
10 x 1.5 is the thread pitch

I would only use 10.9 hardness bolts in this application, but that is just me.

Sealant on both sides of the gasket, just around the block opening is fine.

No oil cooler outlet on water pump is normal for non oil cooler engines.

:beer:
 
Thx Poser and Eddy!!! Is your reccomendation based upon corrosion??? Will clean up threads with Tap and now will have 4 bolts!!!! Is there any reason why Toyota only uses the 1/2 circle for its bolts????
 
Any idea what the bolts should be torqued to??
 
Is there any reason why Toyota only uses the 1/2 circle for its bolts????

If you draw a line between each bolt hole you will see the pattern encircles the port completely. I suspect the holes are in the parts of the block that have yhe most structural metal behind them.

The torque is in this thread: https://forum.ih8mud.com/threads/torques-for-water-pump-bolts-needed.824719/

which you could have found with a google search for "2f water pump bolt torque". Use the google, Luke.
 
Thanks all but have run in to another problem. Dropped my permatex sprayed gasket not once but twice into the dirt......time for a new gasket!!!!!!!!!!!! It seems it is very difficult to line up bolts have gasket in place, hope it does not fall out between the block and pump................another shot weekend. Lately it seems ALL I do is work on it......no drive time. Any one else feels this way at times???? So my question is should I remove front bumper and drop or remove grill so getting at this area would be easier?? More work I know but seems as though I could be in a WAY better position to get this job completed? How do other people do this job?? Thanks all.
 
glue the gasket to the pump. two bolts in holes. lower the works by the bolts down to the block and run the two bolts in as far as you can by hand.
 
Thanks again brian-how about easier access by lowering the grill and removing front bumper??
 
Radiator out and replaced pipe and a couple hoses as well.................
 
FWIW - The OEM water pump gasket I just installed on my '77 looks like this one below. I applied a light/thin coat of Toyota FIPG on the WP side of the gasket first. Then placed it on the WP aligning the bolt holes. Then applied a light/thin coat of Toyota FPIG on the block side. Waited a few minutes, then installed it on the block.


IMG_2478.webp
 
Thanks guys-just a tough reach with my aftermarket 4X style front bumper. Tired when I attempted it.....maybe being rested will make it easier next go round. Gotta clean up that block side again. GA what is FIPG?? I used the NAPA Permatex red spray gasket stuff
 
My pump is an Aisin from SOR, non oil cooler model with round hole opening for the block. The block opening of course looks like your gasket....problem or are all the OEM style pumps that way?
 
My pump is an Aisin from SOR, non oil cooler model with round hole opening for the block. The block opening of course looks like your gasket....problem or are all the OEM style pumps that way?

Tom - I know the OEM (16110-61070 8/76 to 1/79) water pump that was on mine had the round hole. It was the Aisin (TEQ) water pump for the clutch fan and no oil cooler port. It was mentioned to me to put the FIPG on both sides of the the gasket, around the block opening on the gasket, and thin enough so the FIPG doesn't ooze into the block opening. The new aftermarket Airtex water pump I just installed had the same round hole, but the gasket looked just like the OEM gasket.................That's my $.02 worth, out of my last quarter, now I'll spend the other $.23 on some bubble gum. :hillbilly:
 
GA and beno you guys rock!!!!!!!!!!!!!! Looks like I know where I am going from here! BTW GA how is the '77 coming along???
 
GA and beno you guys rock!!!!!!!!!!!!!! Looks like I know where I am going from here! BTW GA how is the '77 coming along???

My 40 is a pleasure to drive these days. Most all major work is completed and just basically using it as my DD. The next major work will be rebuilding the front knuckles this Fall, and Kurt (Cruiser Outfitters) will be putting a kit together for me here soon.
 
Back
Top Bottom