JimJ
ATOYOHOLIC
WANTED 60 PARTS: Looking for a good lower rear gate, a grey/blue front drivers seat but would settle with either side, and a couple front fender marker lights, and a complete carpet in ok shape too. thanks!
VI: Buy/Sell/Trade, In Search Of (1 Viewer)
- Thread starter bikersmurf
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Found the rear springs... still looking for a front or passenger seat. ..
I could use a set of shocks for the 61. Couple inches of lift I think.
No I haven't measured....
No I haven't measured....
- Thread starter
- #604
I've got the a good seat cover for a Fj40 passenger seat +/- 74.
I'd trade you for an iou for some welding on my p/s conversion..
FYI the seat backs and bases can be swapped side to side.
Last edited:
I am looking for a bucket seat..
But will give you a hand with welding... not a problem. . Are u wanting to plate and sleeve the frame for the steering box.????
But will give you a hand with welding... not a problem. . Are u wanting to plate and sleeve the frame for the steering box.????
- Thread starter
- #606
That's the plan, but it'll still be a ways off. I was figuring I'd sleeve the frame with extra thick wall tubing (or 1.5" round stock bored through), plate the inner frame rail. I wasn't planning on welding plate to the outer frame just sandwiching it between the box and the 'tube'. Part of that is because I'm not a welder, and a part is I'd rather not weld on the main frame rail if it's avoidable. I know that many have welded on 40 frames, but it's certainly not something I take lightly.
I've got two U-joints, a slip joint (shaft), a Scout box, and a couple P/S Pumps. One of these days, I'll cut off the rag joint, machine flats onto the steering shaft to the U-Joint, and then sort out the box mounting and drag links.
Unfortunately, the timing chain is toast... or at least I'm hoping all it is, the floor needs attention, and in a fantasy world rear 1/4 panels.
I've got two U-joints, a slip joint (shaft), a Scout box, and a couple P/S Pumps. One of these days, I'll cut off the rag joint, machine flats onto the steering shaft to the U-Joint, and then sort out the box mounting and drag links.
Unfortunately, the timing chain is toast... or at least I'm hoping all it is, the floor needs attention, and in a fantasy world rear 1/4 panels.
Last edited:
Saw 3 80 series trucks between Duncan and Nanaimo the other day so I figure I should post this here too..
For Sale: - 80 Series ARB Rear bumper, Tire Carrier & Jerry Can swingouts - BC Canada
For Sale: - 80 Series ARB Rear bumper, Tire Carrier & Jerry Can swingouts - BC Canada
JimJ
ATOYOHOLIC
Looking to buy a 12V 3B starter, let me know!
need one or need one to be operational?
JimJ
ATOYOHOLIC
Need one to be operational, but I am going to tear into it to see if there is any hope....
JimJ
ATOYOHOLIC
Anyone need a brand new clutch, pressure plate and throw out bearing for a 40 series?
Brian Roberts Auto Electric will rebuild anything
It's usually just the solenoid contacts if it's doing the "click" thing...
I have a Mastercraft metal cut off saw. I don't use it anymore. I'm gone away again by Wed. If you are interested
let me know, I'm thinking $25 cause you have to pick it up here.
UPDATE: SOLD
let me know, I'm thinking $25 cause you have to pick it up here.
UPDATE: SOLD
Last edited:
JimJ
ATOYOHOLIC
Hope someone buys it cause its your turn to buy the beer!! haha
Anyone have some 40 series SOA driveshafts kicking around they would want to sell? Or some early fj60/minitruck driveshafts with double cardan joints? also does anyone have some diff gears (9.5 inch) with a ratio of 4:56, 4:88's or something around that ratio? Im cheap and dont want to have to buy new gears $$$$
Anyone have some 40 series SOA driveshafts kicking around they would want to sell? Or some early fj60/minitruck driveshafts with double cardan joints? also does anyone have some diff gears (9.5 inch) with a ratio of 4:56, 4:88's or something around that ratio? Im cheap and dont want to have to buy new gears $$$$
I have some double cardan joints in the garage...
