Transmission hump

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 6, 2011
Threads
257
Messages
3,115
Location
Woodstock,GA
I installed a 2f motor with a 4speed transmission into my 74 fj40 on Monday and realized that the hole where the shifter goes into the transmission doesn't line up with the hole cut out on the transmission hump.
My FJ40 was a 3speed before. I hate to cut my transmission hump due to its being in great shape. I rather sell it to someone than make the hole bigger.
Does anyone know if a 75-78 transmission hump line up with the same holes to mount to the tub as the 74? Or any other problems that might be an issue? Thanks in advance.
 
Pictures of my transmission hump.
20181120_144650.webp
20181120_144656.webp
20181120_144710.webp
20181120_144713.webp
 
I am certain that the later four speed hump has the same bolt pattern as your hump. Specter Off road sells a gasket set that is interchangeable for three and four speed transmission arrangements.

I have a 1973 three speed, and I'm in need of a transmission hump, so if you decide to sell, please let me know and I'll be happy to work out a deal with you.
 
@cims1970fj40 what route did you take? My 1976 FJ40 from South America has the exact same transmission tunnel cover as yours. The holes will not line up for my H42 upgrade. I’m looking for a cardboard template from someone who has their hump out of their truck to trace for some fabrication work. I’ve posted it here. I’m surprised with so many conversions, there’s no sheet metal plate available from the vendor community.

 
@cims1970fj40 what route did you take? My 1976 FJ40 from South America has the exact same transmission tunnel cover as yours. The holes will not line up for my H42 upgrade. I’m looking for a cardboard template from someone who has their hump out of their truck to trace for some fabrication work. I’ve posted it here. I’m surprised with so many conversions, there’s no sheet metal plate available from the vendor community.

I ended up buying a 4speed cover from someone here on Mud and sold my 3speed cover afterwards.
I didn’t want to modify the 3speed because it was in excellent condition and figured someone else could utilize it. I waited until I found a 4speed before I sold the 3speed cover.
I agree with you about the template. Do you have anyone local that my have one laying around to make a template off of? I know your in Maine and not sure if Cruisers are hard to come by there. Also are you doing the patch work yourself if you can get a template?
 
@cims1970fj40 what route did you take? My 1976 FJ40 from South America has the exact same transmission tunnel cover as yours. The holes will not line up for my H42 upgrade. I’m looking for a cardboard template from someone who has their hump out of their truck to trace for some fabrication work. I’ve posted it here. I’m surprised with so many conversions, there’s no sheet metal plate available from the vendor community.




Here is my 73 three speed (orange) transmission hump
IMG_20200817_092118711.webp
and what I believe is a 78 four speed (blue).
IMG_20200817_091528163.webp


Believe your three speed hump like the one above except it has two drain holes for the cowl vent. US models always had a factory heater so in 74 the vent was welded close. The drains were run thru firewall like previous years. 75 drains moved transmission hump. Personally I would see if someone local had four speed hump to compare. Transfer opening changed 9/73 to same as used on the four speed. If it is in a different location would be the question. If close I would see above enlarging the transmission opening.

Few year after 74 had the floor drain holes in the hump. Then like 74 there are no holes.
 
Thanks for the reply. I would have to travel from MA to NH to Cruiser Parts to trace the shifter holes on a four speed transmission hump. I'm in a conversation with JT Outfitters in North Carolina who manufactures a 4 speed fiberglass cover to make a template of the cutouts. Ideally I will create a kit inclusive of cut out template and metal plate with welded nuts (for the shift boot collars) for others who are looking for a clean modification of their transmission hump. The kit can be done in ones shop or handed off to a metal fabricator to do it. In my case, I will hand it off to a fabricator.

Below are the before pictures. I'll post images once I modify the transmission hump to accommodate the 4 speed.
Fj40 3 speed to 4 speed hump cover.webp

Fj40 3 speed to 4 speed hump cover side.webp
 
Here is my 73 three speed (orange) transmission humpView attachment 2744644and what I believe is a 78 four speed (blue).View attachment 2744641

Believe your three speed hump like the one above except it has two drain holes for the cowl vent. US models always had a factory heater so in 74 the vent was welded close. The drains were run thru firewall like previous years. 75 drains moved transmission hump. Personally I would see if someone local had four speed hump to compare. Transfer opening changed 9/73 to same as used on the four speed. If it is in a different location would be the question. If close I would see above enlarging the transmission opening.

Few year after 74 had the floor drain holes in the hump. Then like 74 there are no holes.
I believe in 78 the cowl drain hole was no longer in the transmission hump due to no longer having the drainage vent on the cowl. But you know a hell of a lot more than I do. Also like you said the transfer case side of the hump is not the problem as far as the location between the 3speed and 4speed. However on the transmission I believe if I would have made the hole larger on the 3speed hump to accommodate the 4speed transmission the hole would have been to large for the 4speed shifter boot to cover it up.
 
Thanks for the reply. I would have to travel from MA to NH to Cruiser Parts to trace the shifter holes on a four speed transmission hump. I'm in a conversation with JT Outfitters in North Carolina who manufactures a 4 speed fiberglass cover to make a template of the cutouts. Ideally I will create a kit inclusive of cut out template and metal plate with welded nuts (for the shift boot collars) for others who are looking for a clean modification of their transmission hump. The kit can be done in ones shop or handed off to a metal fabricator to do it. In my case, I will hand it off to a fabricator.

Below are the before pictures. I'll post images once I modify the transmission hump to accommodate the 4 speed.
View attachment 2744723
View attachment 2744724
I would consider trying to find a nice 4speed hump vs trying to modifying the 3speed one. That’s a nice transmission hump and you wouldn’t have a problem selling it. If you were doing the mods on it yourself it might be worth keeping it. Not sure how much it would be for someone else to modify it but you may be paying more to do that than just finding a good 4speed hump and selling yours to break even or a least close to breaking even.
Here is a picture of the 4speed hump I bought. It’s the one on the left. It came out of a BJ from Europe. The individual I bought it from lives in Texas. Maybe he still has the red one. I’ll look for his user name soon.

67B15C8A-F3F1-481E-A566-D892DCDEE568.webp
 
Back
Top Bottom