Trail Tailor Offerings- Racks, Sliders, Control Arms and Misc (1 Viewer)

[TRAIL TAILOR]

I know it’s a smaller market but any chance you’ll make an AHC sensor bracket on your UCA ?

Only current market is SPC and I’d much rather give you my $

I was going to start with the 100 only. Shoot me a PM or email with a couple pics and a measurement of the OEM tab and what size bolt it needs and I can make a little tab off one side. I can offer those on a "lead time" basis, but would always try to keep a couple on the shelf for the 470 guys.

Jason

 

[atnolan94]

Jason,

Looking at your extended sway bar end links for the rear. It looks like I need to replace the bushing that is inside the end of the sway bar as well. I assume your end link do not come with this? Does anyone know a p/n or aftermarket bushing? I’m having a hard time finding it online for some reason.

Thanks!

 

[TRAIL TAILOR]

Jason,

Looking at your extended sway bar end links for the rear. It looks like I need to replace the bushing that is inside the end of the sway bar as well. I assume your end link do not come with this? Does anyone know a p/n or aftermarket bushing? I’m having a hard time finding it online for some reason.

Thanks!

Should be these- 90385-11021 - Genuine Toyota BUSH, STABILIZER LINK

I used to stock those but by the time I put a mark up on the, no one would buy them.

Jason

 

[ERMB]

Hey Jason,
Do you happen to have any pics of what your UCA's look like as a finished product or did I miss that somewhere? I've been following the progress since you made the announcement so I'm looking forward to when these become available!

 

[atnolan94]

Jason, I know you're busy but any picture updates? Thanks!

 

[TRAIL TAILOR]

Hey Jason,
Do you happen to have any pics of what your UCA's look like as a finished product or did I miss that somewhere? I've been following the progress since you made the announcement so I'm looking forward to when these become available!

Jason, I know you're busy but any picture updates? Thanks!

I'm finishing up this Patrol build and then I will finish the UCAs. I should have pics by the middle of next week.

 

[Homey55]

I'm finishing up this Patrol build and then I will finish the UCAs. I should have pics by the middle of next week.

When will those start to get shipped out? I'm looking to install my lift over Christmas break and it would be nice to do it all at once.

 

[TRAIL TAILOR]

When will those start to get shipped out? I'm looking to install my lift over Christmas break and it would be nice to do it all at once.

Final parts arrived from the machine shop yesterday. Next week I will finish and send to powder. Then ship them out.

J

 

[TRAIL TAILOR]

Patrol was just loaded on the transport truck and now I have 3 open orders to finish. 2 sets of UCAs and one set of RLCAs.

Otherwise I'm closed and this is what you'll see on out contact page along with a completely sold out inventory.

Trail Tailor is closed until February 1, 2019 (no orders will be accepted, online or custom)

 

[Qtonic]

Shoot me a PM or email with a couple pics and a measurement of the OEM tab and what size bolt it needs and I can make a little tab off one side. I can offer those on a "lead time" basis, but would always try to keep a couple on the shelf for the 470 guys.

Did you get what you need for the AHC bracket? If not I can try tomorrow. I'd sure prefer these over other options.

 

[TRAIL TAILOR]

Did you get what you need for the AHC bracket? If not I can try tomorrow. I'd sure prefer these over other options.

Nothing yet.

J

 

[civil offroad]

Patrol was just loaded on the transport truck and now I have 3 open orders to finish. 2 sets of UCAs and one set of RLCAs.

Otherwise I'm closed and this is what you'll see on out contact page along with a completely sold out inventory.

Trail Tailor is closed until February 1, 2019 (no orders will be accepted, online or custom)

Jason... Go have yourself a well deserved break. Andrea and yourself have had one hell (no pun intended) of a 2018!! And you just moved to Kali for starters. Wouldn't want the fireworks show to scare you away. I did have a custom project for you in mind, but since my rig will be heading over to @benc. The down time will allow my mind wander dreaming of a SAS for my 100. Oh the possibilities from some of the best metal workers on the West Coast! Have a safe Holiday and see you next year! Till then... Happy Trails...

 

[TRAIL TAILOR]

UCA arms are bent. Love that new CNC bender. Now to set up the notch jig and we'll be good to go.

First 10 sets are bent. Should have them all to powder by Thursday.

Jason

 

[atnolan94]

UCA arms are bent. Love that new CNC bender. Now to set up the notch jig and we'll be good to go.

First 10 sets are bent. Should have them all to powder by Thursday.

Jason

View attachment 1856937

Nice! Ready to ship February 1st, I assume?

 

[TRAIL TAILOR]

Nice! Ready to ship February 1st, I assume?

I'll ship out a couple sets that are prepaid on TourFlex kits. Looking at late Dec./first of Jan on shipping once we get back from vacation.

J

 

[atnolan94]

I'll ship out a couple sets that are prepaid on TourFlex kits. Looking at late Dec./first of Jan on shipping once we get back from vacation.

J

Awesome no worries at all.

 

[TRAIL TAILOR]

Thanks for the patience on these.

J

 

[TRAIL TAILOR]

Early LX470 HWM Tester headed out to a willing participant for test fitting.

J

 

[yotasavg]

Early LX470 HWM Tester headed out to a willing participant for test fitting.

J

View attachment 1857231

What is the LX470 difference? Bumper tabs?

 

[half k cruiser]

Early LX470 HWM Tester headed out to a willing participant for test fitting.

J

View attachment 1857231

Just got an LX470, going to have to cruise through the other 23 pages of this thread and see what offerings you have for them. Looks like business is booming Jason. Happy holidays.