Three link... has anyone ever...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 1, 2004
Threads
245
Messages
3,540
Location
Staunton, VA
cut the front bushing off the radius arms and added an upper link? I've got an extra set of radius arms and ruffstufd has the link setup for pretty cheap. It would be completely reversible if it didn't work.

I ran the 3-link calculator on it and it doesn't seem too bad. I'll post it up later for those that know more than I.

Someone has to have done this....
 
Depending on caster, allowed travel, the arms will run into the tie rod. There isn't enough clearance in the stock arms, so it will work, but likely isn't much to be gained over narrowed arms.
 
What they said........They know their sh*t. BTDT
 
Have you nothing else to do? 3 links are definitely cool but unnecessary. Two locked diff''s and ground clearance get the job done here in eldorado county.
 
Poor man's 3link. It'll work, but those OE axle brackets will rip off in no time. You may have to completely redo the brackets at the axle. And at that point you might as well create new links.


You think? In my mind they were under more stress with the radius arm set up. Obviously I'm no engineer though.
 
Depending on caster, allowed travel, the arms will run into the tie rod. There isn't enough clearance in the stock arms, so it will work, but likely isn't much to be gained over narrowed arms.


I hadn't thought of this. That makes it pretty strong case against trying it.
 
Have you nothing else to do? 3 links are definitely cool but unnecessary. Two locked diff''s and ground clearance get the job done here in eldorado county.

You know how the mind works. I have an extra set arms and I've been been spending too much time over on pirate.
 
You think? In my mind they were under more stress with the radius arm set up. Obviously I'm no engineer though.

Those OE brackets are really really thin. Bent mine pretty bad using the hitch-pin mod. You can easily bend them with a few taps of the hammer. With just one attachment point on each end of the axle, not something I would trust to hold the axle in place.

I hadn't thought of this. That makes it pretty strong case against trying it.

This would be the least of my concerns as it's easily fixed by moving the steering up front with a RHD arm.
 
How about running a poor boy style version of the Super flex arm , but with tubing? This is a thought that I have been kicking around. The top tube would have a threaded adjustment for caster.
Screenshot_2016-08-26-14-19-47-1.webp
Screenshot_2016-08-26-13-58-13-1.webp
 
Those OE brackets are really really thin. Bent mine pretty bad using the hitch-pin mod. You can easily bend them with a few taps of the hammer. With just one attachment point on each end of the axle, not something I would trust to hold the axle in place.



This would be the least of my concerns as it's easily fixed by moving the steering up front with a RHD arm.

If I did it I would reinforce the bracket. That would be fairly easy.

If I moved the steering up front I'd go ahead and do a 3-link with straight tube. No use keeping the factory arms at that point.

I was imagining this for a low lift, minimal work approach to caster adjustment and a little extra travel. I'd have to get under there and do some measuring.

I was hoping someone who'd done it would post up a picture to satisfy my curiosity.
 
How about running a poor boy style version of the Super flex arm , but with tubing? This is a thought that I have been kicking around. The top tube would have a threaded adjustment for caster.
View attachment 1362168 View attachment 1362169

You can get one of the DIY radius arms from Rough Stuff. Would probably be pretty easy to make it work. You'd have to make sure the bottom tube was long enough to accommodate the bend.
 
How about running a poor boy style version of the Super flex arm , but with tubing? This is a thought that I have been kicking around. The top tube would have a threaded adjustment for caster.
View attachment 1362168 View attachment 1362169
There's a ram 1500 build on pirate running this type of arm (WFO brackets) setup and it works really well. When I was thinking of swapping axles on my last 80 series, this was the route I was going to go.
 
I have one bolt in my front right radius arm right now. The stock mounting plates have been reinforced by the castor plates. Yes I know this is not ideal, yes I keep a close close eye on it, yes this is getting replaced very soon by my 3 link setup just waiting on the hi-steer arms.

I agree with everyone above, the stock mounts are flimsy, and were designed to be used as radius arm holders not a 3 link pivot point.
 
...
I agree with everyone above, the stock mounts are flimsy, and were designed to be used as radius arm holders not a 3 link pivot point.

I would argue that the radius arm puts more stress on the brackets than a link. I have had a link on the left side of mine for ~10yrs. Like most things under there, the bracket is bent, rock damaged, but after hundreds of trail days, shows no sign of failure.
 
I understand, and without derailing too much I'll explain the brackets further. Yes there is some torsional shear force applied to the brackets when twisted up but the majority of that force is taken up by the bushing mount at the frame. With two connection points on the axle it would appear to me that Toyota had engineered that bracket to mainly resist rotational force (drive force) rather than torsional.

If you remove one of those connection points and use a standard bushing you are putting a much larger than designed for torsional load on those brackets when flexed. As proven by the handfull of us who have bent these brackets by doing the trailer pin hitch mod.

So ultimately; Can you? ya, is it the safest way to do it? no.
 
You know how the mind works. I have an extra set arms and I've been been spending too much time over on pirate.

While I get the "Fun of it" thing - Yeah, time on Pirate will land you a 3 linked FR & a whole lot of other overkill.

Unless you find your current situation limits the trails you run, I'd leave it be - like mentioned if you can get by on lift & tires, it'll pay when you have to panic brake when a dip on a cel cuts you off on the highway.

The arms are free today, what you break down the road probably isn't, right?

I get you though, the fun of it is what leads a lot of Jeep guys into full blown 3-link, coilovered, beadlocked nonsense when they started out with a road Jeep they had in our work parking lot. Now the few that still have theirs are trailered to trailheads (Walker Valley is real local) -since you can fall further faster buying internet parts for a Jeep than an 80 (a blessing I think, makes you think before you 'click').

So while the rig is possibly streetable, but must not be practical as they have old Suburbans to tow with.

Not saying anything about Jose's rig for road manners, just saying a rig built for where you run, at the skill level you're happy with - is really the best setup.
 
I would argue that the radius arm puts more stress on the brackets than a link. I have had a link on the left side of mine for ~10yrs. Like most things under there, the bracket is bent, rock damaged, but after hundreds of trail days, shows no sign of failure.
Mind sharing a pic?
 
Back
Top Bottom