Build The honey badger build

[Mike Shull]

I’m back. Yes, that sounds very good. Brings back fond memories of my 383. I didn’t hear any tire noise. Perhaps the mufflers are too loud?

 

[Firemedic831]

sounds killer.

Thank you

 

[clrussell]

Exhaust shop did fantastic.

 

[Firemedic831]

I’m back. Yes, that sounds very good. Brings back fond memories of my 383. I didn’t hear any tire noise. Perhaps the mufflers are too loud?

I will but i needed to get the exhaust done first so i can hook up the 02 and get the sniper tuned .

 

[Mike Shull]

What type of pipe did they use? It looks amazing.

 

[Firemedic831]

It’s 2.5. I could not go 3 because of how it has to fit around the rear links . The collector is really cool I had not seen that before. Last time they had to just notch out 1 of the pipes But this time they did a very clean job for me . It sounds like a pack of pigs oinking lol

 

[Firemedic831]

I also had them put a joint and use v band clamps So if for any reason I do need to work on anything I do not have to pull the entire system out .

 

[Mike Shull]

I had to stay with 2.5 also. Is that aluminized pipe?

 

[Firemedic831]

I had to stay with 2.5 also. Is that aluminized pipe?

yes

 

[Firemedic831]

I am starting to think what to do next . I am thinking maybe AC and some sort or cool center counsel . Next winter i plan on Framing it . Purely for cosmetics .

 

[Firemedic831]

I figured since I had the interior tore apart I would clean up the floor . Very happy to be putting this pig back together again

 

[Firemedic831]

So many little things to do .

 

[Firemedic831]

I was going to wire up my electric fans to the sniper . ( I had a fan wired before ) but the harness for the sniper 2 is different . . I had bought the sniper pdm. But never installed it . Anyways back when I got the sniper 2 they did not even have a harness at the time . So tonite I figured. Just get the new harness and install the pdm. . It will be a lot cleaner. I just hate redoing things . I think I am going to make a plate that mounts in the glove box. And I can Velcro all these controller boxes to it . With all the Dakota stuff and sniper stuff I want to keep it as clean as I can

 

[Firemedic831]

New harness showed up today so tonite I started installing it . I ran all the wires and hooked up
The pdm. And everything works . Fans come on fuel pump works. This is great . Now I can mount the pdm and shorten the wires and clean that up .

 

[Firemedic831]

The new harness does not have all those relays. Just a much cleaner setup .

 

[Firemedic831]

Cut out more wire. And got the pdm hooked up . Much cleaner now.

 

[Firemedic831]

Everything is working well . I ran it for about 20 min and the fan is kicking on and off like it is supposed to . I am really glad I decided to redo the wiring . Not exactly on my list of fun things to do but it is done . Got the sniper IAC dialed in also. I have a few more weeks to tinker with it before Cruise Moab Next is to get the skid plate mounted

 

[rlong]

Is the sniper sending data to the DD gauges. I’m thinking of using Holley Terminator (stealth w/ throttle body) so I can utilize the Terminator optional transmission control for a 4L60e.

 

[Firemedic831]

Is the sniper sending data to the DD gauges. I’m thinking of using Holley Terminator (stealth w/ throttle body) so I can utilize the Terminator optional transmission control for a 4L60e.

Yes i have the additional control boxes for the Dakota digital gauge cluster so the Sniper ties into that as well

 

[Firemedic831]

Getting closer . Ugg I decided to use some Pam to lube some tube I was bending. And I knocked the can over it fell and exploded mostly in my face but got on everything . What I flipping mess .