Steering Column Shell

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 10, 2011
Threads
38
Messages
1,924
Location
Lawrenceville GA
Does anyone make an upgrade to the factory steering column shell cover?? I've fixed it several times and now it's just ziptied which works except it's making contact with my signal arm and that causes very short turn signals. I dont mind the price of a new one but if it's broken once it will again and I dont want to keep wasting $$$ on this.
 
Mine was broken in several places on the inside where the little "towers" that have holes in the bottom where the screws go are. I saw what the price was on a new one and ended up using some epoxy putty to fashion a repair that beefed up the towers and held the busted parts in the right place. I have one lap of electrical tape around the outside that kinda holds it tight together, but you don't even notice it because it is black and the shell is in great shape and sturdy now. I would either do what I did or beef up a new one the same way. It's those towers that give you trouble, that and wrassling the wheel up and down all the time, which I don't do.
 
Yeah I guess I could do that with a new one and beef it up a bit. I just figured with all the 3d printing capabilities someone might have upgraded it. This is a common issue when I started searching.
 
The clamshells for '93-'94 are the worst. Very brittle. Mine did the same as Red's and I did the epoxy fix as well. I hear the '95-'97 clamshells are much more robust but may require some fiddling to get them to work. I have one from a '97 LC with oak interior that I plan to paint black and attempt to retrofit into my '94 some day.
 
Figures, mines a 94.

I've glued it so much I would have to buy a new one at this point
Maybe not. I actually epoxied a washer that was the same size as the old hole had been into mine because the old stuff was pretty dinged up and a couple parts were missing altogether. I recall having to figure out how long it needed to be, but once I got that dialed in, it was pretty easy. I just roughed up the surface with some extra coarse sandpaper and let it set up for a couple of days.
 
Yeah I guess I could do that with a new one and beef it up a bit. I just figured with all the 3d printing capabilities someone might have upgraded it. This is a common issue when I started searching.
You should see about a 3D printing option. It might be worth modifying a new one that has been built up and then scanning that for the replacement. I doubt it would be cheaper, but there would be a market for a permanent solution for all of us with the '93-'94.
 
Nothing to report on yet

I’m not working on anything. I’m just patiently waiting for Joey to break his clamshell so it becomes a priority! :rofl:
 
I’m not working on anything. I’m just patiently waiting for Joey to break his clamshell so it becomes a priority! :rofl:
Maybe we can help? Seriously, all it takes is letting someone else who is short drive the Cruiser. Hop in with the seat too close and your knee smashes the column and its game over for the clamshell.
 
I just ponied up the cash and got a new one from @beno . No probs since. Last one was good for twenty something years so hopefully this one will last a few years.
 
Maybe we can help? Seriously, all it takes is letting someone else who is short drive the Cruiser. Hop in with the seat too close and your knee smashes the column and its game over for the clamshell.

If you haven’t met Joey, it will be tough finding someone shorter...
:rofl:
 
I haven't had to worry about it because after I bought the truck that was one of the first things to come off, it was so busted up and just sitting on the column and rattling. would be nice to get a new one but ive been fine with out a cover
 
Umm, I’m 6’

6’3” when I’m wearing your heels :flipoff2:

Sorry. I’ve been surrounded by Dutch women for the past 3 days. Every. Single. One. Is 6’3”+. It’s god damn torture!!
 
Back
Top Bottom